2009 Lancer Ralliart - GST Basemap
#5056
Evolving Member
iTrader: (1)
I'm bring my car back to stock, and have a test pipe and K&N panel filter but am getting a P0420.
I was wondering what map to run to not throw this code because of the test pipe. I want to say use the tbe and switch the wgdc to the stock pill? But not sure so I'm asking, thanks!
I was wondering what map to run to not throw this code because of the test pipe. I want to say use the tbe and switch the wgdc to the stock pill? But not sure so I'm asking, thanks!
Also check if DTC P0140 is set to 8000 units.
#5058
Evolving Member
iTrader: (1)
Karma got me. Yesterday I reflashed the BoostPill+TBE on my car and got the same code. Took me some time trying to remember what I did. But now I know.
On the latest ECUFlash software openup your firmware.
Scroll down to the ECU Options section
Click on the checkbox for ECU Options Set #2
On the new window that will pop up, look at the section that says "Enable Rear O2 Sensor" and set the bit to 0.
Upload new firmware to the car
Enjoy
On the latest ECUFlash software openup your firmware.
Scroll down to the ECU Options section
Click on the checkbox for ECU Options Set #2
On the new window that will pop up, look at the section that says "Enable Rear O2 Sensor" and set the bit to 0.
Upload new firmware to the car
Enjoy
#5059
Which GST map do i use
i have a muffler delete and resonator delete and a boostpill and ur resonated testpipe which gst map will be best for my mods
Last edited by Nick Hernandez; Dec 19, 2018 at 01:19 AM.
#5060
Galant fortis 2012 ralliart tune?
Is it possible to put the same usdm rom into my Galant fortis ralliart which is a JDM? Because here in New Zealand we use 98 petrol as our highest. If possible could someone do a tune for me?😅 If not could I have the basic modifications to the base rom and I'll do it myself. Also if someone can get me the base 98 tune could someone get me the other 2, boost pill and the other one😁 thank you!
#5061
Is it possible to put the same usdm rom into my Galant fortis ralliart which is a JDM? Because here in New Zealand we use 98 petrol as our highest. If possible could someone do a tune for me?😅 If not could I have the basic modifications to the base rom and I'll do it myself. Also if someone can get me the base 98 tune could someone get me the other 2, boost pill and the other one😁 thank you!
Also, 98 RON is about the same as our 93 OCT gasoline here in the United States.
#5062
#5063
#5064
ID Found, now what?
alright so i found the id and all,[16:26:12.837] J2534 API Version: 04.04[16:26:12.837] J2534 DLL Version: 1.02.4798 Jun 13 2016 17:17:10[16:26:12.837] Device Firmware Version: 1.17.4877[16:26:12.837] Device Serial Number: TAQrLDVh[16:26:14.718] -- reading ECU ID --[16:26:15.242] ECU HW part number : 1860B484[16:26:15.262] ECU SW part number : 1860B48402[16:26:15.277] VIN : CY4A-0800227[16:26:15.277] interface close[16:26:15.279] interface close *please help
#5066
Basemap without exhaust
Sorry to bring up an old post, however say i have a 2010 ralliart with boostpill and aem intake but stock exhaust would i just run the upgraded boostpill basemap?
Cheers
Cheers
#5067
EvoM Staff Alumni
iTrader: (3)
Hey welcome aboard. Im a EvO9 owner so cant really offer any advice on your question, but if you dont get an answer go ahead a post up a new thread w/your question
Cheers, Joe
#5068
Evolved Member
Hi. As you've noticed, a stock exhaust and AEM Intake isn't a combination that is covered by the Base Maps.
Running a non-AEM map with an AEM Intake is likely to mess with your fuel trims, as the measured air calcs will be out.
Rich
Running a non-AEM map with an AEM Intake is likely to mess with your fuel trims, as the measured air calcs will be out.
Rich
#5069
The cars already got the intake installed however is throwing CEL's for the 2nd o2 sensor havin a slow response, guessing due to the higher air flow, its still on its stock tune so to speak.
I have a boostpill sitting here hence the idea of just running the basemap for that, i am however lookin into gettin the exhaust sorted as soon as the funds become available. In the meantime i was just curious as to what i could run until i finally got around to sortin the exhaust.
The fuel Trims being out would this cause issues other than runnin rich or should i still be good to run that map for the time being?
Cheers Dom
I have a boostpill sitting here hence the idea of just running the basemap for that, i am however lookin into gettin the exhaust sorted as soon as the funds become available. In the meantime i was just curious as to what i could run until i finally got around to sortin the exhaust.
The fuel Trims being out would this cause issues other than runnin rich or should i still be good to run that map for the time being?
Cheers Dom
#5070
Evolved Member
The cars already got the intake installed however is throwing CEL's for the 2nd o2 sensor havin a slow response, guessing due to the higher air flow, its still on its stock tune so to speak.
I have a boostpill sitting here hence the idea of just running the basemap for that, i am however lookin into gettin the exhaust sorted as soon as the funds become available. In the meantime i was just curious as to what i could run until i finally got around to sortin the exhaust.
The fuel Trims being out would this cause issues other than runnin rich or should i still be good to run that map for the time being?
Cheers Dom
I have a boostpill sitting here hence the idea of just running the basemap for that, i am however lookin into gettin the exhaust sorted as soon as the funds become available. In the meantime i was just curious as to what i could run until i finally got around to sortin the exhaust.
The fuel Trims being out would this cause issues other than runnin rich or should i still be good to run that map for the time being?
Cheers Dom
If you're reasonably technically minded, it is feasible for you to suss out how to copy the MAF scaling table content from a GST Base Map "AEM" ROM image into your own tune... and voila, you should have accurate LTFT again.
Rich