ECUFlash / Evoscan / Mitsulogger Questions
#1172
Evolving Member
iTrader: (4)
Join Date: Feb 2010
Location: Belgium
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
UeGO works with EvoScan v2.9 use that.
Also EvoScan v2.5 is available for download on this webpage: http://www.evoscan.com/evoscan-updates
Also EvoScan v2.5 is available for download on this webpage: http://www.evoscan.com/evoscan-updates
Thanks for the tip evoscan.
Now I still have another issue to fix. I can't get Load 1Byte to log.
Request ID in evoscan is 41 so I opened ecuflash, opened my rom, went to the MUT table and changed the value in MUT41 to 0x840B.
I then flashed my ecu with the modified rom and tried logging but it doesn't work, just says 0 all the time.
Is there anything else I need to do?
I'm on rom 88840016.
#1174
Evolving Member
iTrader: (20)
Join Date: May 2011
Location: michigan
Posts: 380
Likes: 0
Received 0 Likes
on
0 Posts
I tried checking any DTC's with mine since my CEL light is burned out and I got
CHECK DTC's Complete. In the DTC box it says "No response from vehicle ecu" does that = no codes?
#1176
Evolved Member
Join Date: May 2011
Location: New Zealand
Posts: 964
Likes: 0
Received 0 Likes
on
0 Posts
No, it will say scan complete and the quantity of DTCs found. Try starting evoscan, connecting the cable to the vehicle then switching the key to the on position, with a 10 sec gap between each step then checking for DTCs. Sometimes it has hard time connecting, I know mine does most times.
#1178
Evolving Member
evo 9-open port 1.3
I never had any problems logging with evoscan from 2.5 to 2.8 but since switching to 2.9 I have this : "Object reference not set to an instance of an object"
Is it because I re-arranged the lines so I have those I use the most on top ?
It doesn't seem to do this all the time, I'm pretty sure it's one or several values that when logged cause this. I tried logging the bare minimum rpm,tp,adv,airflow,afrmap,afr,knocksum and had no errors.
I never had any problems logging with evoscan from 2.5 to 2.8 but since switching to 2.9 I have this : "Object reference not set to an instance of an object"
Is it because I re-arranged the lines so I have those I use the most on top ?
It doesn't seem to do this all the time, I'm pretty sure it's one or several values that when logged cause this. I tried logging the bare minimum rpm,tp,adv,airflow,afrmap,afr,knocksum and had no errors.
#1180
Thanks in advance.
- Paul
#1181
Evolved Member
iTrader: (30)
I've been getting a FTDI read timeout error -4 with Evoscan v2.7.0070. Even with anti-virus disabled while logging.
Using an HP mini 210-1018 CL
I'm stumped.
Also I noticed that it's initializing at 5 baud. Shouldn't it be higher than that?
Using an HP mini 210-1018 CL
I'm stumped.
Also I noticed that it's initializing at 5 baud. Shouldn't it be higher than that?
Last edited by EVO8emUp; Feb 7, 2012 at 07:27 AM.
#1182
Evolving Member
Like Zman15, it may be because of my LC-1 WB, I'll try not to log it.
Won't be able to give you an update soon sadly, it's impossible to datalog properly these days, we now have between 15 and -2.2°F outside temp where I live the engine oil temp doesn't go above 158°F and it takes an hour to reach it ><
#1184
Hamish,
I am running v2.9.0017.
Any ideas or suggestions for my problem?
Thanks,
- Paul
I am running v2.9.0017.
Any ideas or suggestions for my problem?
Evo 9 running Tephra 88590715 and using OP2.0 to connect to the ECM. It happens when I log "External Wideband A/F Ratio" and the signal goes lean - basically when I lift off the throttle, my LC-1 goes really lean and times out in a way. At least that what seems to happen in LogWorks. This was never an issue running EvoScan 2.7 on Windows XP, but now I'm running EvoScan 2.9 on Windows 7. I did not run EvoScan 2.7 on my Win7 machine. Also, I don't think I can blame the serial to usb adapter because it does fine when it's in range. Any other ideas?
- Paul
#1185
i cant log any of my fuel trims, only o2 feed back. Mut table is stock.
Im trying to set latencies and scaling on my 1000cc PTE injectors. I tried the ones on the fuel injector thread with no success.
Im trying to set latencies and scaling on my 1000cc PTE injectors. I tried the ones on the fuel injector thread with no success.