ECUFlash / Evoscan / Mitsulogger Questions
#1231
Evolving Member
iTrader: (13)
Hello, I just began the process of remote tuning.
I sent my current ROM off, and just got a bin file base map tune for speed density back.
When I go to open it in ECUFlash I get an error stating: "Unknown ROM Image"
What is there I can do?
Along with the base map, I also recieved the Tephra V7 mod (xml file). I placed it exactly where instructed to.
My question is, do I have to modify something to do with the TephraMod before ECUFlash will accept the SD base map?
Thanks for any help!
I sent my current ROM off, and just got a bin file base map tune for speed density back.
When I go to open it in ECUFlash I get an error stating: "Unknown ROM Image"
What is there I can do?
Along with the base map, I also recieved the Tephra V7 mod (xml file). I placed it exactly where instructed to.
My question is, do I have to modify something to do with the TephraMod before ECUFlash will accept the SD base map?
Thanks for any help!
#1233
Silver Sponsor
iTrader: (-1)
nope its as simple as you describe.. just drop the xml into the rommetadata evo folder, and close/open ecuflash. you probably got some old xmls from somewhere..
try and download the latest from www.evoscan.com/roms/mitsubishi
try and download the latest from www.evoscan.com/roms/mitsubishi
#1234
Evolved Member
iTrader: (49)
Evoscan is giving me issues.
It's datalogging very slowly it's like it's lagging, it's behind 2-3 seconds from the actual values it should be.
What it's doing is the first item will log then it goes to the next so on and so forth until it reaches the last item to log and then it goes back to the first item.
So it's only reading one value at a time then going through the rest and loops again and again.
It's datalogging very slowly it's like it's lagging, it's behind 2-3 seconds from the actual values it should be.
What it's doing is the first item will log then it goes to the next so on and so forth until it reaches the last item to log and then it goes back to the first item.
So it's only reading one value at a time then going through the rest and loops again and again.
#1235
Okay, made progress. I can scan my DTCs using MUTIII, but not OBD2. How accurate are the codes if I use MUTIII on an evo8? I get vehicle speed sensor and barometric speed sensor, sometimes neither, sometimes both, sometimes one, sometimes the other. It's very inconsistent.
My only problem is a high idle, which sometimes goes low and full lean.
My only problem is a high idle, which sometimes goes low and full lean.
#1241
Evolving Member
iTrader: (4)
Join Date: Feb 2010
Location: Belgium
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
I found this but it's no good (for 88840016)
<table name="Ignition Trim vs Air Temp" category="Timing" address="3c8e" type="2D" level="2" scaling="Enrich">
<table name="Air Temp" address="70e6" type="X Axis" elements="8" scaling="Temp"/>
</table>
Anyone got the correct address for this?
<table name="Ignition Trim vs Air Temp" category="Timing" address="3c8e" type="2D" level="2" scaling="Enrich">
<table name="Air Temp" address="70e6" type="X Axis" elements="8" scaling="Temp"/>
</table>
Anyone got the correct address for this?
#1244
I have an evoscan issue
I can't get it to connect or go "live" with my ecu
Mitsulogger works and reads fine tho
Evoscan can Read my ECU and DL the Rom..
but I can't connect and read CEL codes, or pretty much anything else..
I've tried fiddling with all the settings.. everything looked normal.. but it just doesn't work..
i've tried installing diff versions etc.
I have an EDM evo 9
what is mitsulogger doing that EvoScan can't?
any suggestions?
I can't get it to connect or go "live" with my ecu
Mitsulogger works and reads fine tho
Evoscan can Read my ECU and DL the Rom..
but I can't connect and read CEL codes, or pretty much anything else..
I've tried fiddling with all the settings.. everything looked normal.. but it just doesn't work..
i've tried installing diff versions etc.
I have an EDM evo 9
what is mitsulogger doing that EvoScan can't?
any suggestions?
#1245
Evolving Member
iTrader: (1)
Evoscan and a USDM 2003 Evo 8.
I am completely new at this so be gentle. I just purchased Tactrix OP2.0 and installed the latest v2.9.0021 software. It seems like I cant display DTCs or log. At the received Data/Eventlog window I get:
Info: OpenPort 2.0 found
Info: OpenPort firmware v1.11.320
Info: Battery 12,134V
Info: initalize vehicle ecu...
Info: OBDII connecting...
Info: Initializing at 5 baud...
info: Initializing complete...
Info: No response from Vehicle ecu
Info: check DTCs complete.
I have tried Openport 1.3x and 2.0, OBDII 96+ and Mitsubishi MUTIII at device setup.
I also choose the OBDII EFI (all 1996-2006 i.e. Evo7/8/9)
Anyone have any idea what I have done wrong?
Thanks
I am completely new at this so be gentle. I just purchased Tactrix OP2.0 and installed the latest v2.9.0021 software. It seems like I cant display DTCs or log. At the received Data/Eventlog window I get:
Info: OpenPort 2.0 found
Info: OpenPort firmware v1.11.320
Info: Battery 12,134V
Info: initalize vehicle ecu...
Info: OBDII connecting...
Info: Initializing at 5 baud...
info: Initializing complete...
Info: No response from Vehicle ecu
Info: check DTCs complete.
I have tried Openport 1.3x and 2.0, OBDII 96+ and Mitsubishi MUTIII at device setup.
I also choose the OBDII EFI (all 1996-2006 i.e. Evo7/8/9)
Anyone have any idea what I have done wrong?
Thanks