oh[U] sorry I meant evoscan...can I just edit with cable and evoscan? what does anyone recommend for what I am after just getting limiter cut which is set to 112 miles per hr here,raising turbo cut slighty af if not still set to 100 ron from japan or at least 98 ron as best Australia has also set octane rating abit higher...what would be best way to change these? just 1.3r or U cable and evonscan and I can edit these and set straight back in to stock ecu? or I need to re-ecuflash after changing those things?

 

Getting this error:
Error: Unable to load DLL 'op20pt32.DLL': The specified module could not be found. (Exception from HRESULT: 0x8007007E)

Also giving me the ftd2xx.dll not found error when I made sure to put it in the windows system32 dir
I'm using a 1.3DA cable so why is it giving me this error?

 

Search and ye shall find the answer https://www.evolutionm.net/forums/6936737-post546.html (you lazy bum)

 

Unfortunately my problem is now
Info: OpenPort Firmware v1.12.368
Info: Battery 13.245V
Info: Initialize Vehicle ECU...
Info: Initializing At 5 baud...
Info: Timer: 2116.2263ms
Info: Initialization Complete...
Info: Waiting for INIT Response...
Error: J2534 Read Error - 16
Info: Datalogger Ended.


Searching resulting in
https://www.evolutionm.net/forums/ec...rror-16-a.html

 

hello everyone
i have a problem i can not log zeitronix data to evoscan using both serial cable and the OBD II in zeitronix datalogger i can see the AFR,boost,TPS and RPM working very good. also i read that zeitronix datalogger has to be close while datalogging on evoscan but still not working the com port in correct on evoscan i seleted the right wideband tick the data i want to datalog but still not getting any data
any help please?

 

Did you select the COM port in evoscan to match the zeitronix ?

 

yes it is selected properly

 

^ I am having the exact same problem.

Zeitronix software picks up the information fine but in evoscan, its all zeros. I have selected the right com port and wb unit from the list. I have also restarted the laptop with the usb-serial cable. I have used two different cables. All the same result.

fyi, using latest version of both software.

 

I am getting the "no response from vehicle ecu"
Anyone know how to fix this.
Using a 1.3u cable

Thanks

 

Update:
Got it working, after changing baud rate to 62500.

 

I have the same issue with AEM UEGO through a serial port. I have selected the right com port and everything. I am going to try the 62500 baud number change and see what happens.

 

Tried it, and it did not work!!! Arrhhhh, How can I get EVOSCAN to read my wideband again!!!!

 

was it ever working before?

click on WIDEBAND and click on open com port manager, and view the port, does it show up in there as it was installed successfully (no exclamation mark)?

 

i had the exact some problem and i try everything it never worked i know my answer for the problem something you dont want to hear but what i did that i used another laptop and it was pretty fine

 

Guys , Has anyone experience AYC failure ? below is my DTC log ...

Hope someone could explain what is the problem

Diagnostic Codes:12 Val. Power Supply
0xC0 And 0x02 Unknown DTC
26 Speed Sensor
25 Deformed Tyre
24 Rear Left Sensor Open
23 Rear Right Sensor Open
22 Front Left Sensor Open
21 Front Right Sensor Open
0xC1 And 0x01 Unknown DTC
0xC1 And 0x02 Unknown DTC
0xC1 And 0x04 Unknown DTC
41 TPS Open
34 ST-1,2 Short
33 Fixed ST-N High
32 ST-N Short
31 ST Sensor Open
0xC2 And 0x01 Unknown DTC
65 ABS Monitor
0xC2 And 0x04 Unknown DTC
61 Stop Lamp Switch
0xC2 And 0x10 Unknown DTC
56 G Force Sensor (Lateral)
52 G Force Sensor (Stick)
51 G Force Sensor (Straight)
0xC3 And 0x01 Unknown DTC
83 Pump Fail 2
82 Pump Fail 1
81 Pump Relay
0xC3 And 0x10 Unknown DTC
73 Left Direct Valve
72 Right Direct Valve
71 Proportion. Valve