EVOSCAN and LC-1(LC1) question
Feb 18, 2007, 12:40 PM
#17
I have an LC-1 and it works just fine with logworks but I need it to work with EVOSCAN.
The values that EVOscan logs read like this(idle values).
4.8265
4.8314
4.8412
4.8461
4.8559
4.8706
4.8902
4.9
4.8951
4.8804
Any idea's?
Yes it is set up to LC-1 and the correct com port.
Yes I searched.
Thanks in advance.
The values that EVOscan logs read like this(idle values).
4.8265
4.8314
4.8412
4.8461
4.8559
4.8706
4.8902
4.9
4.8951
4.8804
Any idea's?
Yes it is set up to LC-1 and the correct com port.
Yes I searched.
Thanks in advance.
If not, do another heater calibration but instead of 20 seconds try 60 seconds (cold outside) then do another free air.
Problem is the readings should go no lower than 7.8 with LC1
Just select LC1 WB and use the default COM for evoscan
Feb 19, 2007, 03:34 PM
#18
Evolving Member
Thread Starter
iTrader: (10)
Join Date: Sep 2006
Location: Pittsburgh
Posts: 230
Likes: 0
Received 0 Likes
on
0 Posts
I got it to work. In LM Programmer software I had to set the drop down box(there is only one) to the proper value.
Now evoscan works just fine. You need to restart the car in order for changes to take effect.
This is for an innovate LC-1(lc1) wideband.
Now evoscan works just fine. You need to restart the car in order for changes to take effect.
This is for an innovate LC-1(lc1) wideband.
Feb 19, 2007, 10:16 PM
#21
i havent decided yet, i just bought a laptop and i'm still looking at all my options. i just like the minimalism of the lc1... i might do a gauge eventually.
Honestly I wanted to DIY a wbo2 controller but the calibration, plus heating circuitry make it a little more than i'm willing to spend time on. The pricepoint on the LC1 makes DIY not even worth it.
mj, would you hurry it up with that already?
Honestly I wanted to DIY a wbo2 controller but the calibration, plus heating circuitry make it a little more than i'm willing to spend time on. The pricepoint on the LC1 makes DIY not even worth it.
mj, would you hurry it up with that already?
Feb 20, 2007, 05:48 AM
#22
Evolved Member
iTrader: (19)
Join Date: Sep 2005
Location: Butthole, MA
Posts: 834
Likes: 0
Received 0 Likes
on
0 Posts
i havent decided yet, i just bought a laptop and i'm still looking at all my options. i just like the minimalism of the lc1... i might do a gauge eventually.
Honestly I wanted to DIY a wbo2 controller but the calibration, plus heating circuitry make it a little more than i'm willing to spend time on. The pricepoint on the LC1 makes DIY not even worth it.
mj, would you hurry it up with that already?
Honestly I wanted to DIY a wbo2 controller but the calibration, plus heating circuitry make it a little more than i'm willing to spend time on. The pricepoint on the LC1 makes DIY not even worth it.
mj, would you hurry it up with that already?
The LC-1 is relatively cheap.
Thread
Thread Starter
Forum
Replies
Last Post
3vo|3oost
General Engine Management / Tuning Forum
6
May 7, 2017 01:10 AM
Rokpapaziz
Evo X Engine Management / Tuning Forums
11
Jun 6, 2013 12:30 AM
