PATCH: CEL Flash on Loaded Knock
#151
Evolving Member
iTrader: (1)
Join Date: Mar 2007
Location: Coastal Maine
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, but Id like it to be darn near close to 0 counts, so I think Id rather put up with the extra flashing. Kindof reminds me to keep my foot out of it until I get my tune sorted out.
Oh, and Ive got mine set to Load=100, knock count=3
Oh, and Ive got mine set to Load=100, knock count=3
Last edited by Charlie_B; Aug 23, 2007 at 07:02 AM.
#153
Evolved Member
iTrader: (18)
I had my flash setup to read up to 300 on the load cell scaling by a mail-in tuner a while back...since the 'how to' for this MOD hasn't been fully released *only with an already patched file* how do i go about increasing the load cells on the patch? Is it as easy as deleting load cell '70' and '90' and adding '280' and '300' at the end on the fuel/timing maps (along with the adjusting of the maps in those areas) or is it more in depth? Some help will be greatly appreciated! I have rom 96940011 if that matters...
Also i logged 'Load Calculated' and '2-Byte load' at the same time at idle and it seems that those two work while both on...
Also i logged 'Load Calculated' and '2-Byte load' at the same time at idle and it seems that those two work while both on...
#154
Evolved Member
iTrader: (22)
I had my flash setup to read up to 300 on the load cell scaling by a mail-in tuner a while back...since the 'how to' for this MOD hasn't been fully released *only with an already patched file* how do i go about increasing the load cells on the patch? Is it as easy as deleting load cell '70' and '90' and adding '280' and '300' at the end on the fuel/timing maps (along with the adjusting of the maps in those areas) or is it more in depth? Some help will be greatly appreciated! I have rom 96940011 if that matters...
Also i logged 'Load Calculated' and '2-Byte load' at the same time at idle and it seems that those two work while both on...
Also i logged 'Load Calculated' and '2-Byte load' at the same time at idle and it seems that those two work while both on...
https://www.evolutionm.net/forums/sh...ight=rescaling
But you are basically on the right track.
#155
Evolved Member
iTrader: (18)
Step by step to rescale load:
https://www.evolutionm.net/forums/sh...ight=rescaling
But you are basically on the right track.
https://www.evolutionm.net/forums/sh...ight=rescaling
But you are basically on the right track.
Another question....
Does anybody know if the 96940011 ROM has the dealer po300 fix on it? My old rom didnt and when i went to flash it changed about 5 different sections of code (when its doing the crc check to see what was modified or not)
#159
Really big thanks to tephra
I patched his altered rom code with my previous 88840016 tune, and it works fine !
I set the load to 120 and KS to 4 (so I get warned above 3 on serious load), and this makes me more confortable when I'm driving hard without any loggin
I patched his altered rom code with my previous 88840016 tune, and it works fine !
I set the load to 120 and KS to 4 (so I get warned above 3 on serious load), and this makes me more confortable when I'm driving hard without any loggin
#160
Newbie
Join Date: Aug 2007
Location: old testament god of the squirrels
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Using the v15 of the EVO IX rom, when I went to look at the values, the default time was something like 23xxx (don't have the exact number in front of me) instead of 3xxx. Has anyone else seen this? Did I do something wrong? I didn't flash the ROM since I was afraid something wasn't correct.
Thanks,
MIke
Thanks,
MIke
#161
Evolved Member
iTrader: (66)
Using the v15 of the EVO IX rom, when I went to look at the values, the default time was something like 23xxx (don't have the exact number in front of me) instead of 3xxx. Has anyone else seen this? Did I do something wrong? I didn't flash the ROM since I was afraid something wasn't correct.
Thanks,
MIke
Thanks,
MIke
Also noticed that after the knock map each and every flash afterwards took much longer than expected.
#162
Account Disabled
iTrader: (3)
Join Date: Apr 2006
Location: USA
Posts: 1,029
Likes: 0
Received 0 Likes
on
0 Posts
I'd highly suggest turning the load reached before cel flash down to 0. Reason being so that you can see part throttle knock (which changes with each brand of gas or tank to tank from same brand) so that you can watch the knock sensor at all times. I caught a 2500rpm 90% load tip in issue this way (that went away with a new tank of gas). Also evo 9's seem to pull MUCH more timing per count of knock than 8's. I'd recommend 3 as a good starting point for knock threshold for cel flash and evo 8's can probably stand upwards of 5 before timing pull becomes a serious issue. Even on my evo 9 a single counts was pulling extreme amount of timing for some reason.
Last edited by dan l; Aug 27, 2007 at 02:50 PM.
#163
Evolved Member
iTrader: (66)
Here is what my settings ended up changing to..... scared the crap out of me.
......and this is after I had already had this working.
IRT setting the load to zero.... I often see phantom knock at low loads. I really do not care to see that activity. I want to know about knock when at 200 and above.
......and this is after I had already had this working.
IRT setting the load to zero.... I often see phantom knock at low loads. I really do not care to see that activity. I want to know about knock when at 200 and above.
Last edited by Jeff_Jeske; Aug 27, 2007 at 02:51 PM.