PATCH: TephraMod V5
#48
#49
EvoM Staff Alumni
iTrader: (16)
If I am running ECU controlled boost, can i eliminate my #2 and #3 baseline boost tables as well?
edit: Another question, i noticed your O2 Sim Hook and Subroutine do not match Mrfreds from the other thread, is that supposed to be? Maybe you moved it to another place in memory?
edit: Another question, i noticed your O2 Sim Hook and Subroutine do not match Mrfreds from the other thread, is that supposed to be? Maybe you moved it to another place in memory?
Last edited by MR Turco; Mar 18, 2008 at 08:28 AM.
#51
Evolving Member
iTrader: (4)
Would it be possible to have the voltage for map switching configurable?
default would be something like:
aggressive = 5V
if voltage >= aggressive then run the aggressive maps
else run the conservative maps
For example I have a GM fuel composition sensor converted to 0-5V analog and I'd like to be able to set it to run my E85 maps if the signal is over 3.4 volts (68% ethanol), and run my 92oct map if it's lower than that.
I still hope for an interpolating flex fuel rom some day =) but this would work good enough in the mean time
default would be something like:
aggressive = 5V
if voltage >= aggressive then run the aggressive maps
else run the conservative maps
For example I have a GM fuel composition sensor converted to 0-5V analog and I'd like to be able to set it to run my E85 maps if the signal is over 3.4 volts (68% ethanol), and run my 92oct map if it's lower than that.
I still hope for an interpolating flex fuel rom some day =) but this would work good enough in the mean time
#52
EvoM Staff Alumni
iTrader: (16)
Would it be possible to have the voltage for map switching configurable?
default would be something like:
aggressive = 5V
if voltage >= aggressive then run the aggressive maps
else run the conservative maps
For example I have a GM fuel composition sensor converted to 0-5V analog and I'd like to be able to set it to run my E85 maps if the signal is over 3.4 volts (68% ethanol), and run my 92oct map if it's lower than that.
I still hope for an interpolating flex fuel rom some day =) but this would work good enough in the mean time
default would be something like:
aggressive = 5V
if voltage >= aggressive then run the aggressive maps
else run the conservative maps
For example I have a GM fuel composition sensor converted to 0-5V analog and I'd like to be able to set it to run my E85 maps if the signal is over 3.4 volts (68% ethanol), and run my 92oct map if it's lower than that.
I still hope for an interpolating flex fuel rom some day =) but this would work good enough in the mean time
#54
Evolved Member
iTrader: (55)
the auto valet mode is getting turned off as soon as i get a chance...everytime you shut the car off and start it the car goes into valet mode. Kinda cool but annoying at the same time(holding down the gas pedal for every start.)
Jamie - still not working for switching modes...every other feature works fine. I left it at Teph's default 3.01volts.
Jamie - still not working for switching modes...every other feature works fine. I left it at Teph's default 3.01volts.
#56
Evolved Member
iTrader: (26)
Join Date: Nov 2005
Location: San Diego, CA
Posts: 717
Likes: 0
Received 0 Likes
on
0 Posts
OT....sorry guys.
#57
Evolved Member
iTrader: (17)
The LED works but its not switching maps? If you have a volt meter, check the harness wire going into the unused location for voltage and see what readings you are getting. You can datalog the voltage at the ADC input in evoscan or mitsulogger. Unfortunately I don't know which address you'd need to use in your MUT table to do it, which ROM ID do you have? It was 0x8929 in my 94170014. The eval formula I used in evoscan was (x/256)*5 to read the voltage input. I just threw the 0x8929 in an unused MUT location in my 3D MUT Table. I believe MUT 83 shows the ALT map switching and will show a 0 when its in standard maps and 1 when its in the ALT maps. Worst case, I'll have you send that one back and I'll priority mail you a new one.
#59
Evolved Member
iTrader: (19)
Join Date: Oct 2004
Location: CT
Posts: 885
Likes: 0
Received 0 Likes
on
0 Posts
the auto valet mode is getting turned off as soon as i get a chance...everytime you shut the car off and start it the car goes into valet mode. Kinda cool but annoying at the same time(holding down the gas pedal for every start.)
Jamie - still not working for switching modes...every other feature works fine. I left it at Teph's default 3.01volts.
Jamie - still not working for switching modes...every other feature works fine. I left it at Teph's default 3.01volts.
Jack of All Trades:
Have you tested the 94170014?