PATCH: TephraMod V5
#64
Evolving Member
iTrader: (3)
Join Date: Jul 2006
Location: Cedar Rapids, IA
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
I don't quite understand the following statement in the directions for 88590015:
"4) Remove your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore"
I have ECUFlash 1.34. I only show one high octane fuel and one low octane fuel map, and then the 3 high octane ignition maps and 3 low octane ignition maps as follows:
<table name="High Octane Fuel Map" address="2dbd">
<table name="Engine Load" address="6ec8" elements="20" scaling="Load"/>
<table name="RPM" address="6ea0" elements="15"/>
</table>
<table name="Low Octane Fuel Map" address="2ef5">
<table name="Engine Load" address="6ec8" elements="20" scaling="Load"/>
<table name="RPM" address="6ea0" elements="15"/>
</table>
<table name="High Octane Ignition Map 1" address="33e9">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="Low Octane Ignition Map 1" address="3599">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="High Octane Ignition Map 2" address="5523">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="Low Octane Ignition Map 2" address="56d3">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="High Octane Ignition Map 3" address="5a33">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="Low Octane Ignition Map 3" address="5be3">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
What about fuel am I supposed to remove? I gather that I am to remove the #2-3 low and high octane ignition table entries. It's fuel I'm confused about.
"4) Remove your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore"
I have ECUFlash 1.34. I only show one high octane fuel and one low octane fuel map, and then the 3 high octane ignition maps and 3 low octane ignition maps as follows:
<table name="High Octane Fuel Map" address="2dbd">
<table name="Engine Load" address="6ec8" elements="20" scaling="Load"/>
<table name="RPM" address="6ea0" elements="15"/>
</table>
<table name="Low Octane Fuel Map" address="2ef5">
<table name="Engine Load" address="6ec8" elements="20" scaling="Load"/>
<table name="RPM" address="6ea0" elements="15"/>
</table>
<table name="High Octane Ignition Map 1" address="33e9">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="Low Octane Ignition Map 1" address="3599">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="High Octane Ignition Map 2" address="5523">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="Low Octane Ignition Map 2" address="56d3">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="High Octane Ignition Map 3" address="5a33">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
<table name="Low Octane Ignition Map 3" address="5be3">
<table name="Engine Load" address="6f2c" elements="21" scaling="Load"/>
<table name="RPM" address="6efa" elements="20"/>
</table>
What about fuel am I supposed to remove? I gather that I am to remove the #2-3 low and high octane ignition table entries. It's fuel I'm confused about.
Last edited by Shadowpriest; Mar 18, 2008 at 03:35 PM.
#65
EvoM Staff Alumni
iTrader: (16)
If I am running ECU controlled boost, can i eliminate my #2 and #3 baseline boost tables as well?
edit: Another question, i noticed your O2 Sim Hook and Subroutine do not match Mrfreds from the other thread, is that supposed to be? Maybe you moved it to another place in memory?
edit: Another question, i noticed your O2 Sim Hook and Subroutine do not match Mrfreds from the other thread, is that supposed to be? Maybe you moved it to another place in memory?
#68
EvoM Guru
iTrader: (8)
I don't quite understand the following statement in the directions for 88590015:
"4) Remove your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore"
I have ECUFlash 1.34. I only show one high octane fuel and one low octane fuel map, and then the 3 high octane ignition maps and 3 low octane ignition maps as follows:
"4) Remove your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore"
I have ECUFlash 1.34. I only show one high octane fuel and one low octane fuel map, and then the 3 high octane ignition maps and 3 low octane ignition maps as follows:
#69
Evolved Member
iTrader: (17)
Or use the Evo VIII harness for now and I will send you the IX pin when they come in, free of charge. I have about 6-7 members using the VIII harness with a IX ECU right now. Its a tight fit in the unused pin location, its just that the VIII pin has no way to "lock" in so they just ziptie the wire to the factory harness to keep if from moving. Good enough until the pins come in
#70
If I am running ECU controlled boost, can i eliminate my #2 and #3 baseline boost tables as well?
edit: Another question, i noticed your O2 Sim Hook and Subroutine do not match Mrfreds from the other thread, is that supposed to be? Maybe you moved it to another place in memory?
edit: Another question, i noticed your O2 Sim Hook and Subroutine do not match Mrfreds from the other thread, is that supposed to be? Maybe you moved it to another place in memory?
The O2Sim is the same algorithm as MrFred but implemented slightly differently
Cheers
Dave.
#72
Evolved Member
iTrader: (55)
The LED works but its not switching maps? If you have a volt meter, check the harness wire going into the unused location for voltage and see what readings you are getting. You can datalog the voltage at the ADC input in evoscan or mitsulogger. Unfortunately I don't know which address you'd need to use in your MUT table to do it, which ROM ID do you have? It was 0x8929 in my 94170014. The eval formula I used in evoscan was (x/256)*5 to read the voltage input. I just threw the 0x8929 in an unused MUT location in my 3D MUT Table. I believe MUT 83 shows the ALT map switching and will show a 0 when its in standard maps and 1 when its in the ALT maps. Worst case, I'll have you send that one back and I'll priority mail you a new one.
#73
Yes - sorry I should say:
With regards to "removing" 2/3 (timing/bdel/bwgd) its upto you, but probably renaming the table to something like "original name + DONT USE" might be best.
That way you can still "see" it, but you get a visual reminder not to use it!
Cheers
D.
With regards to "removing" 2/3 (timing/bdel/bwgd) its upto you, but probably renaming the table to something like "original name + DONT USE" might be best.
That way you can still "see" it, but you get a visual reminder not to use it!
Cheers
D.