PATCH: TephraMod V5
#771
Evolving Member
iTrader: (22)
Join Date: Feb 2008
Location: Lansdowne Pa
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
Hey,im not sure if this is your problem but i was haveing the same issue last night.I was trying to disable the rear o2 with MrFred's xml code.I kept adding the code and it wouldnt show up.After an hour i saw when i would save the xml file it would save the file as administrator,so i opened ecuflash as admistrator and bam there were the tables.Vista ftl again,like i said might not be your problem but might be someone elses.
#772
Evolved Member
iTrader: (3)
However, my car is actually running on ROM ID 94170008. Since this ROM is not supported, I'm (attempting) upgrading to ROM ID 94170014. I'm editing the XML for 94170014 in Mistu/EVO folder in ECUflash dir.
I think I'm doing everything exactly as Jamie shows in the video.
The notes in the V5 patch file say:
"NOTES:
1) Change your ENDIAN just below, ECUFlash version 1.31 and higher = "big", 1.30 and lower = "little"
2) Remove your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
3) Remove your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
4) Please test the features of this rom before driving off, if anything doesn't work as expected report back to Tephra."
Note #1 is obviously referring to the XML file.
Do notes #2 and #3 also refer to the XML, or to the BIN file? The notes do not specify, however the video does NOT show "removing" these; it only shows not using them in the future.
#773
Evolved Member
iTrader: (3)
Hey,im not sure if this is your problem but i was haveing the same issue last night.I was trying to disable the rear o2 with MrFred's xml code.I kept adding the code and it wouldnt show up.After an hour i saw when i would save the xml file it would save the file as administrator,so i opened ecuflash as admistrator and bam there were the tables.Vista ftl again,like i said might not be your problem but might be someone elses.
#775
EvoM Guru
iTrader: (8)
I'm editing the actual specific ROM ID file that came with ECUflash for ROM ID 94170014.
However, my car is actually running on ROM ID 94170008. Since this ROM is not supported, I'm (attempting) upgrading to ROM ID 94170014. I'm editing the XML for 94170014 in Mistu/EVO folder in ECUflash dir.
I think I'm doing everything exactly as Jamie shows in the video.
The notes in the V5 patch file say:
"NOTES:
1) Change your ENDIAN just below, ECUFlash version 1.31 and higher = "big", 1.30 and lower = "little"
2) Remove your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
3) Remove your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
4) Please test the features of this rom before driving off, if anything doesn't work as expected report back to Tephra."
Note #1 is obviously referring to the XML file.
Do notes #2 and #3 also refer to the XML, or to the BIN file? The notes do not specify, however the video does NOT show "removing" these; it only shows not using them in the future.
However, my car is actually running on ROM ID 94170008. Since this ROM is not supported, I'm (attempting) upgrading to ROM ID 94170014. I'm editing the XML for 94170014 in Mistu/EVO folder in ECUflash dir.
I think I'm doing everything exactly as Jamie shows in the video.
The notes in the V5 patch file say:
"NOTES:
1) Change your ENDIAN just below, ECUFlash version 1.31 and higher = "big", 1.30 and lower = "little"
2) Remove your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
3) Remove your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
4) Please test the features of this rom before driving off, if anything doesn't work as expected report back to Tephra."
Note #1 is obviously referring to the XML file.
Do notes #2 and #3 also refer to the XML, or to the BIN file? The notes do not specify, however the video does NOT show "removing" these; it only shows not using them in the future.
#777
EvoM Guru
iTrader: (8)
Also, you need to use the .hex / bin file that for 94170014 that is in the first post of this thread. You *cannot* use a different 94170014 file, as it doesnt have the mods done to it. This could be another reason why you cant see the tables.
YOU HAVE TO USE THE 94170014.hex file supplied by tephra.
YOU HAVE TO USE THE 94170014.hex file supplied by tephra.