Evo 10 - Ecuflash - 3 tables
#63
Evolved Member
iTrader: (5)
mrfred. I think that might be a memory register to the can interface.
page 13-63 is very similar type address.
http://documentation.renesas.com/eng...48_32180um.pdf
page 13-63 is very similar type address.
http://documentation.renesas.com/eng...48_32180um.pdf
Last edited by Mr. Evo IX; Jun 7, 2008 at 07:13 PM.
The following users liked this post:
biela (Aug 12, 2021)
#67
I'm in
"The EIT vector entry is located at the beginning of the internal ROM/extended external areas. The branch instruction
for jumping to the start address of each EIT event processing handler is written here. Note that it is the branch
instruction and not the jump address itself that is written here."
The first bytes are actual code, not a vector... change it to code and you can start to disassemble the code. I'm moving house in 48 hours and have boxes everywhere, wish I could play more! I still get some register errors so I think we need the right processor definition or setup.
"The EIT vector entry is located at the beginning of the internal ROM/extended external areas. The branch instruction
for jumping to the start address of each EIT event processing handler is written here. Note that it is the branch
instruction and not the jump address itself that is written here."
The first bytes are actual code, not a vector... change it to code and you can start to disassemble the code. I'm moving house in 48 hours and have boxes everywhere, wish I could play more! I still get some register errors so I think we need the right processor definition or setup.
Last edited by jcsbanks; Jun 8, 2008 at 02:41 AM.
#69
Former Sponsor
iTrader: (10)
Found some more stuff, but it could be hit and miss
-Injector Latency
Battery Voltage Scale Offset: 608fc elements "7" - 99% sure correct
Injector Latency MS Offset: 556cc - 45% sure
-Boost Target Maps 1-2-3 ???
Offset: 5e623
Offset: 5e719
Offset: 5e80f
scaling uint8??? or possibly boostbar???
X axis offset: 61690 scaling boostbar?? elements "14"
Y axis offset: 63710 RPM?? elements "17"
Any input on these maps would be much appreciated!
-Injector Latency
Battery Voltage Scale Offset: 608fc elements "7" - 99% sure correct
Injector Latency MS Offset: 556cc - 45% sure
-Boost Target Maps 1-2-3 ???
Offset: 5e623
Offset: 5e719
Offset: 5e80f
scaling uint8??? or possibly boostbar???
X axis offset: 61690 scaling boostbar?? elements "14"
Y axis offset: 63710 RPM?? elements "17"
Any input on these maps would be much appreciated!
#71
EvoM Guru
iTrader: (5)
Nice.. I definitely will be getting myself a new CAN/Openport cable, and an ECU and building a bench harness to work at it sometime in the future.
I have to buy a new car some time in the future.. It might end up being an X or Ralliart (the AWD turbo if they release it) so I've been watching this stuff, but not participating much.
I have to buy a new car some time in the future.. It might end up being an X or Ralliart (the AWD turbo if they release it) so I've been watching this stuff, but not participating much.
#75
Evolved Member
iTrader: (17)
Its crazy that I forsee the X ECU to be almost completely disassembled before there is even enough aftermarket goodies to slap on one of them,lol. I guess the VIII and IX's were a practice run to get everyone ready to rip the X ecu apart haha. Great work guys. Damn I want an X now.