TephraMOD V5.10
#1067
#1069
Thank you. I was able to get 1byte working.
I tried to log it and as quickly as it starts to spool, it hits that brick wall. it was only at a load of 192.9 when it stopped. 3312 RPM.
I can post the log if that will help
edit, unable to figure out how to post the log
Stock IX turbo and boost pill removed
I tried to log it and as quickly as it starts to spool, it hits that brick wall. it was only at a load of 192.9 when it stopped. 3312 RPM.
I can post the log if that will help
edit, unable to figure out how to post the log
Stock IX turbo and boost pill removed
Last edited by INEVOIX; May 31, 2009 at 10:39 PM.
#1072
Well I'm not 100% sure.
I completely started from scratch and made sure everything was copied over correctly. I did find a discrepancy in the MUT table that I missed (didn't copy) the first time.
This time I also disabled:
"enable auto-valet on fresh ignition"
"enable MAP Averaging" After researching more, I realized this was for the JDM 3 BAR or other MAP scensor. Obviously since I don't have this, it made sense to disable...lol
Well after all this, I reflashed it and it worked great.
The only thing that didn't show up in my log was the load 1byte. I'll work on that later. It may have been a fluke since it worked earlier.
I completely started from scratch and made sure everything was copied over correctly. I did find a discrepancy in the MUT table that I missed (didn't copy) the first time.
This time I also disabled:
"enable auto-valet on fresh ignition"
"enable MAP Averaging" After researching more, I realized this was for the JDM 3 BAR or other MAP scensor. Obviously since I don't have this, it made sense to disable...lol
Well after all this, I reflashed it and it worked great.
The only thing that didn't show up in my log was the load 1byte. I'll work on that later. It may have been a fluke since it worked earlier.
#1074
NLTS TPS Load Malfuncion with 90550001
Hello,
I read this post where the user TTP has my same problem with NLTS work, but I have this problem with def 90550001.
I made some test on EVO7 (clutch switch manually installed and wired to ECU pin and ground) and EVO8 (clutch switch OEM installed on the same ECU pin):
The TPS load make the cut and the clutch switch don't affect.
I try to disconnect the switch plug too, but the only way to disable this cut is turn OFF the NLTS funcion in the map.
Is it possible that this malfunction depends by the mod's StatRevLimiter?
I made some tests on EVO9 88540014 or 17 and the NLTS works grat, but I see that in those maps the mod's StaRevLimiter is not implemented, only the standard one.
Thanks,
Nik
I read this post where the user TTP has my same problem with NLTS work, but I have this problem with def 90550001.
I made some test on EVO7 (clutch switch manually installed and wired to ECU pin and ground) and EVO8 (clutch switch OEM installed on the same ECU pin):
The TPS load make the cut and the clutch switch don't affect.
I try to disconnect the switch plug too, but the only way to disable this cut is turn OFF the NLTS funcion in the map.
Is it possible that this malfunction depends by the mod's StatRevLimiter?
I made some tests on EVO9 88540014 or 17 and the NLTS works grat, but I see that in those maps the mod's StaRevLimiter is not implemented, only the standard one.
Thanks,
Nik
#1075
EvoM Community Team Leader
iTrader: (60)
another noob here. i don't understand these statements:
1) Change your ENDIAN just below, ECUFlash version 1.31 and higher = "big", 1.30 and lower = "little"
2) Remove/Rename your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
3) Remove/Rename your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
4) Remove/Rename your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore
2) Remove/Rename your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
3) Remove/Rename your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
4) Remove/Rename your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore
#1076
I don't understand what you mean: you simply quote the obvious base settings for mods install...
I think my settings are ok for 90550001: Endian Big (1.41), Boost Desired Engine Load" #2 and #3 removed, Max Wastegate Duty" #2, #3, and #4 removed.
I can't find "Base Wastegate Duty" or "Hi/Lo Octane Fuel+Timing" on this def, but in EVO9 one. I wrote on previous post that I've done tests on EVO9 with excellent results.
---
I just made more tests on EVO7/8 and I think the switch works on the opposite way:
When the switch cable is disconnected the fuel cut come.
When the switch connected, the fuel cut comes when the pedal is released (switch pushed -> OFF).
When I push down a few the pedal (switch extended -> ON) the fuel cut don't come.
This happens on EVO8 too, with OEM switch installed, so I don't think I made mistakes.
Maybe the switch works at the opposite for some reasons linked to the hardware of my ECU?
It could be possible to invert this switch with a different .bin map file?
I think my settings are ok for 90550001: Endian Big (1.41), Boost Desired Engine Load" #2 and #3 removed, Max Wastegate Duty" #2, #3, and #4 removed.
I can't find "Base Wastegate Duty" or "Hi/Lo Octane Fuel+Timing" on this def, but in EVO9 one. I wrote on previous post that I've done tests on EVO9 with excellent results.
---
I just made more tests on EVO7/8 and I think the switch works on the opposite way:
When the switch cable is disconnected the fuel cut come.
When the switch connected, the fuel cut comes when the pedal is released (switch pushed -> OFF).
When I push down a few the pedal (switch extended -> ON) the fuel cut don't come.
This happens on EVO8 too, with OEM switch installed, so I don't think I made mistakes.
Maybe the switch works at the opposite for some reasons linked to the hardware of my ECU?
It could be possible to invert this switch with a different .bin map file?
#1077
Evolved Member
iTrader: (30)
Join Date: Dec 2003
Location: USA
Posts: 929
Likes: 0
Received 0 Likes
on
0 Posts
1) Change your ENDIAN just below, ECUFlash version 1.31 and higher = "big", 1.30 and lower = "little"
Check your Ecuflash version and see if it is 1.31 or above. Your Endian values should = big. Search your Ecuflash XML for "Endian" and look at what you Endian values are. Change if necessary
2) Remove/Rename your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
Search xml for "Boost Desired Engine Load". Remove or comment out #2 and #3, no longer needed
3) Remove/Rename your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
Search xml for "Base Wastegate Duty" Remove or comment out #2 and #3, no longer needed
4) Remove/Rename your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore
Search xml for Hi/Lo Octane Fuel+Timing maps. If you have them, remove or comment out #2 and #3, no longer needed
Check your Ecuflash version and see if it is 1.31 or above. Your Endian values should = big. Search your Ecuflash XML for "Endian" and look at what you Endian values are. Change if necessary
2) Remove/Rename your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
Search xml for "Boost Desired Engine Load". Remove or comment out #2 and #3, no longer needed
3) Remove/Rename your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
Search xml for "Base Wastegate Duty" Remove or comment out #2 and #3, no longer needed
4) Remove/Rename your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore
Search xml for Hi/Lo Octane Fuel+Timing maps. If you have them, remove or comment out #2 and #3, no longer needed
#1079
1) Change your ENDIAN just below, ECUFlash version 1.31 and higher = "big", 1.30 and lower = "little"
Check your Ecuflash version and see if it is 1.31 or above. Your Endian values should = big. Search your Ecuflash XML for "Endian" and look at what you Endian values are. Change if necessary
2) Remove/Rename your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
Search xml for "Boost Desired Engine Load". Remove or comment out #2 and #3, no longer needed
3) Remove/Rename your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
Search xml for "Base Wastegate Duty" Remove or comment out #2 and #3, no longer needed
4) Remove/Rename your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore
Search xml for Hi/Lo Octane Fuel+Timing maps. If you have them, remove or comment out #2 and #3, no longer needed
Check your Ecuflash version and see if it is 1.31 or above. Your Endian values should = big. Search your Ecuflash XML for "Endian" and look at what you Endian values are. Change if necessary
2) Remove/Rename your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
Search xml for "Boost Desired Engine Load". Remove or comment out #2 and #3, no longer needed
3) Remove/Rename your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
Search xml for "Base Wastegate Duty" Remove or comment out #2 and #3, no longer needed
4) Remove/Rename your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore
Search xml for Hi/Lo Octane Fuel+Timing maps. If you have them, remove or comment out #2 and #3, no longer needed
Unfortunately, I can't find the way to work with the stock clutch switch, it works only at the opposite (switch OFF -> CUT / switch ON -> NO CUT).
I'm going to try again, maybe with a different type of switch, but I hope it could be possible to invert the funcion by software soon.