OmniPower 4 bar settings
#47
Evolved Member
iTrader: (2)
First off, you need a very small screwdriver. I used a 1.4mm and that was a tad too big, but it still worked. I'm thinking a 3/64" or smaller may work better.
Anyway, when you take the metal clip off, pull off the plug, then remove the plastic retaining clip.
Then, looking into the plug, there is hole on top of the hole that the pins are in. What you need to do is slide the screwdriver down that other hole, while angling it towards the pin (so it's sort of scraping the pin). Then when you get to the bottom of travel, gently pry the screwdriver away from the pin. There is a little latch there that the pin snaps past, so that it can't be removed. Once you pry that little latch up, try to hold it there and use your other hand to pull the wire out. It should slide out pretty easily.
Here is my attempt at drawing a picture with _ and |
Code:
______ | | <--- hole _|____|_ <--- insert screwdriver here, angled toward pin, then pry up at end | | | | <--- pin |________|
Last edited by l2r99gst; Jun 4, 2009 at 05:01 PM.
#50
Evolved Member
iTrader: (9)
OK, I swapped my wires just now.
First off, you need a very small screwdriver. I used a 1.4mm and that was a tad too big, but it still worked. I'm thinking a 3/64" or smaller may work better.
Anyway, when you take the metal clip off, pull off the plug, then remove the plastic retaining clip.
Then, looking into the plug, there is hole on top of the hole that the pins are in. What you need to do is slide the screwdriver down that other hole, while angling it towards the pin (so it's sort of scraping the pin). Then when you get to the bottom of travel, gently pry the screwdriver away from the pin. There is a little latch there that the pin snaps past, so that it can't be removed. Once you pry that little latch up, try to hold it there and use your other hand to pull the wire out. It should slide out pretty easily.
Here is my attempt at drawing a picture with _ and |
Eric
First off, you need a very small screwdriver. I used a 1.4mm and that was a tad too big, but it still worked. I'm thinking a 3/64" or smaller may work better.
Anyway, when you take the metal clip off, pull off the plug, then remove the plastic retaining clip.
Then, looking into the plug, there is hole on top of the hole that the pins are in. What you need to do is slide the screwdriver down that other hole, while angling it towards the pin (so it's sort of scraping the pin). Then when you get to the bottom of travel, gently pry the screwdriver away from the pin. There is a little latch there that the pin snaps past, so that it can't be removed. Once you pry that little latch up, try to hold it there and use your other hand to pull the wire out. It should slide out pretty easily.
Here is my attempt at drawing a picture with _ and |
Code:
______ | | <--- hole _|____|_ <--- insert screwdriver here, angled toward pin, then pry up at end | | | | <--- pin |________|
#53
Account Disabled
iTrader: (28)
Join Date: Jul 2006
Location: ft. walton beach, FLORIDA
Posts: 1,115
Likes: 0
Received 0 Likes
on
0 Posts
Im not calling you stupid man, Im just trying to help you understand. I mean theres already a diagram he made with instructions so I guess I dont see what your having a hard time understanding.
#54
Evolved Member
iTrader: (2)
There should be three pin connectors each in their own hole and another hole above each of those three holes. My picture was a crude diagram of just one of three pin connectors and it's corresponding hole and hole above it (as if you were looking into the plug).
#57
Evolved Member
iTrader: (2)
You're drawing is just upside down from mine and yours shows three pins where mine showed just one.
But, yes, you insert the screwdriver (it has to be a very, very small screwdriver) into that hole, angled toward the pin. Once you reach the bottom, you them pull/pry away from the pin and hold it there. That releases the latch that holds the pin in there.
If you look closely, the hole looks more like my drawing, where it narrow before connecting to the pin hole. That is how small the screwdriver should be...it needs to fit in there.
But, yes, you insert the screwdriver (it has to be a very, very small screwdriver) into that hole, angled toward the pin. Once you reach the bottom, you them pull/pry away from the pin and hold it there. That releases the latch that holds the pin in there.
If you look closely, the hole looks more like my drawing, where it narrow before connecting to the pin hole. That is how small the screwdriver should be...it needs to fit in there.
Last edited by l2r99gst; Jun 9, 2009 at 07:10 PM.
#59
Evolving Member
iTrader: (4)
Join Date: May 2007
Location: Plymouth, MI
Posts: 327
Likes: 0
Received 0 Likes
on
0 Posts
Bringing this topic back. Did the MAP sensors get added to your store? Maybe I am looking in the wrong sections, but I don't see them in the Electronics section.
Thanks for all the information in setting this up. I'm looking forward to being able to log boost soon.
Thanks for all the information in setting this up. I'm looking forward to being able to log boost soon.
#60
Evolved Member
iTrader: (1)
After installing the omni 4 bar and implementing the proper changes found here and on mrfred's thread, I have found that I'm getting a bad lean condition after boosting then adjusting the throttle back slightly, but still boosting. I loose power, it stumbles for a second, then the afr goes back to normal, all while having the throttle in the previous adjusted position. Can anyone help?
Last edited by D-VO; Aug 12, 2009 at 12:23 PM. Reason: cant add logs