TephraMod V7
#691
Actually no it's not, as currently I'm running the speed density patch with no MAF. It only drops idle under load from the climate control fan, same as it would for when the A/C is on. I'm pretty sure the last time I had this issue I adjusted the A/C idle and the problem went away.
#692
#694
Option 2 - Thanks to recompile 88590715 (v7 + Mods) - Download | Mirror
- Setup for JDM MAP and PSI based boost control (mrfred)
- WGDC Correction Interval set to 1 (Stock = 10)
- Max Total Upward WGDC Correction @ 100% TPS set to 0 (Stock = 10)
- EGR System Disabled (mrfred)
- Max Timing Retard set to -20 degrees (tephra)
- FAA bit.10 disabled ("weird unknown" timing pull at cruise)
- FAA bit.09 disabled (cat-warmup ignition retard)
- FBA bit.00 disabled (lean spool)
- FCA bit.09 disabled (EGR Test)
- OBD Inspection set to Pass all tests (acamus)
- Rear O2 Heater patch applied (mrfred)
- Fuel Cut Load Limit x2 and set to 300 (mrfred)
i have these:
88590015_r3compile_20091010
evo9base_r3compile_20091010
TephraMOD-88590715-v7
which do i use? i keep getting errors that they are "unrecognized roms". it's been a while since i installed 5.1 and set it all up. what am i missing???
Last edited by kaj; Oct 24, 2009 at 12:55 AM.
#695
Was the table to change the value from 0x03 -> 0x0E removed?
In my 94170015 SD ROM I can find it in the SD Programming menu, between SD Disable Baro Error, and SD MAT Scaling. I can't find it in the new SD Programming menu with the 96533706 ROM anywhere.
Am I just blind, or is it actually not present?? Thanks.
#696
so i DL'ed the zip file. i ended up with like two or three different xml files.. it's hard to read either 'cause they look like this:
i have these:
88590015_r3compile_20091010
evo9base_r3compile_20091010
TephraMOD-88590715-v7
which do i use? i keep getting errors that they are "unrecognized roms". it's been a while since i installed 5.1 and set it all up. what am i missing???
i have these:
88590015_r3compile_20091010
evo9base_r3compile_20091010
TephraMOD-88590715-v7
which do i use? i keep getting errors that they are "unrecognized roms". it's been a while since i installed 5.1 and set it all up. what am i missing???
All 3 of those XML's needs to be placed into your 'rommetadata\mitsubishi\evo' folder. They all will be used once you open the 88590715 V7 rom. You will also need to have Ecuflash version 1.41 or higher.
#697
Actually no it's not, as currently I'm running the speed density patch with no MAF. It only drops idle under load from the climate control fan, same as it would for when the A/C is on. I'm pretty sure the last time I had this issue I adjusted the A/C idle and the problem went away.
#698
so i DL'ed the zip file. i ended up with like two or three different xml files.. it's hard to read either 'cause they look like this:
i have these:
88590015_r3compile_20091010
evo9base_r3compile_20091010
TephraMOD-88590715-v7
which do i use? i keep getting errors that they are "unrecognized roms". it's been a while since i installed 5.1 and set it all up. what am i missing???
i have these:
88590015_r3compile_20091010
evo9base_r3compile_20091010
TephraMOD-88590715-v7
which do i use? i keep getting errors that they are "unrecognized roms". it's been a while since i installed 5.1 and set it all up. what am i missing???
Opening the file in Wordpad is a workaround for this problem.
As far as which XML, as stated earlier, make sure all 3 go into your folder, and also make sure you're using the latest version of EcuFlash.
#700
#701
#703
Was the table to change the value from 0x03 -> 0x0E removed?
In my 94170015 SD ROM I can find it in the SD Programming menu, between SD Disable Baro Error, and SD MAT Scaling. I can't find it in the new SD Programming menu with the 96533706 ROM anywhere.
Am I just blind, or is it actually not present?? Thanks.
In my 94170015 SD ROM I can find it in the SD Programming menu, between SD Disable Baro Error, and SD MAT Scaling. I can't find it in the new SD Programming menu with the 96533706 ROM anywhere.
Am I just blind, or is it actually not present?? Thanks.
#704
Already did that 2 days ago just to make sure. It's something to physically do with the IACV when there's an electrical load, similar to the air conditioning being turned on and idle raises...I'm going to look into this more today.
#705
Maybe because the load switching point set in the ECU isn't being reached with your SD setup? Your load values that occur when your lights/AC/accessories turn on might be lower than it normally would have been with the stock MAF setup.