Advanced fuel control options
#256
Evolved Member
iTrader: (6)
Yes it's during spoolup. I've not mess with Lean spool which is disabled from since I had the car. I don't really want to activate it because it's known to be inconsistent.
I'm aware of the exhaust gaz delay, but as soon as I get a little leaner on spoolup I get knock so I think AFR reading may be quite precise.
I'm aware of the exhaust gaz delay, but as soon as I get a little leaner on spoolup I get knock so I think AFR reading may be quite precise.
#257
Evolved Member
I have found lean spool to be quite consistent, the longer are at WOT the richer the fueling, including when going through the gears.
#259
Does anyone has this issue before? I have been looking in the search button but apparently this hasn't been brought up before. It is just about the scaling of the ASYNC Tables see attached. I just copy and paste what mrfred has in the thread post related to the 8859 XML.
P.S. This is for a 8859 XML EVO 9 USDM
Last edited by jmedina23; Apr 25, 2018 at 08:23 AM.
#260
Anything help......If there is somebody with a 8859 XML fully functional and with full capabilities (tables, scaling, etc) let me know so I can test it in my car. I'm getting some issues taking off ( The car lean out entirely below 1K) and I have done everything that people with the same problem have done without any luck.
#261
Evolved Member
Anything help......If there is somebody with a 8859 XML fully functional and with full capabilities (tables, scaling, etc) let me know so I can test it in my car. I'm getting some issues taking off ( The car lean out entirely below 1K) and I have done everything that people with the same problem have done without any luck.
#263
Evolving Member
xml for low pulse width adder evo 9?
Wanted to see if anyone had the data for the "Low pulse width adder" table for a evo 9 that I can add to my .xml file? Can't seem to find it for some reason Rom ID# 8859xxxx
#264
<scaling name="InjLinearizationPWScale" units="PW Adder (ms)" toexpr="x*0.004" frexpr="x/0.004" format="%.3f" min="0" max="0.5" inc="0.004" storagetype="uint8" endian="big"/>
<table name="Injector Flow Linearization PW Adder" category="Fuel" address="31db" type="2D" level="2" scaling="InjLinearizationPWScale">
<table name="Requested FPW (ms)" type="Static Y Axis" elements="66">
<data>0.016</data>
<data>0.048</data>
<data>0.080</data>
<data>0.112</data>
<data>0.144</data>
<data>0.176</data>
<data>0.208</data>
<data>0.240</data>
<data>0.272</data>
<data>0.304</data>
<data>0.336</data>
<data>0.368</data>
<data>0.400</data>
<data>0.432</data>
<data>0.464</data>
<data>0.496</data>
<data>0.528</data>
<data>0.560</data>
<data>0.592</data>
<data>0.624</data>
<data>0.656</data>
<data>0.688</data>
<data>0.720</data>
<data>0.752</data>
<data>0.784</data>
<data>0.816</data>
<data>0.848</data>
<data>0.880</data>
<data>0.912</data>
<data>0.944</data>
<data>0.976</data>
<data>1.008</data>
<data>1.040</data>
<data>1.072</data>
<data>1.104</data>
<data>1.136</data>
<data>1.168</data>
<data>1.200</data>
<data>1.232</data>
<data>1.264</data>
<data>1.296</data>
<data>1.328</data>
<data>1.360</data>
<data>1.392</data>
<data>1.424</data>
<data>1.456</data>
<data>1.488</data>
<data>1.520</data>
<data>1.552</data>
<data>1.584</data>
<data>1.616</data>
<data>1.648</data>
<data>1.680</data>
<data>1.712</data>
<data>1.744</data>
<data>1.776</data>
<data>1.808</data>
<data>1.840</data>
<data>1.872</data>
<data>1.904</data>
<data>1.936</data>
<data>1.968</data>
<data>2.000</data>
<data>2.032</data>
<data>2.064</data>
<data>2.096</data>
</table>
</table>
Thread
Thread Starter
Forum
Replies
Last Post