How To: Speed Density on the evo8 using tephra v7/Phenem pre-patched roms
#331
If you want to have lower values in your VE table, put in a lower value for injector scaling to give you more fuel. Or raise the VE values. I wouldn't bother with MAF scaling too much.
#332
Just made the switch on 88591715...
one question for clarification..
During inital setup at idle and static 3000rpm rev, are we looking to get FEEDBACK or LTFT_LOW as close to zero as possible..
I ask because after 10mins of idling at full temps, mine are:
I'm assuming LTFT_Low as the car seems to be idling just fine.
one question for clarification..
During inital setup at idle and static 3000rpm rev, are we looking to get FEEDBACK or LTFT_LOW as close to zero as possible..
I ask because after 10mins of idling at full temps, mine are:
Code:
FuelTrim_Low O2FeedbackTrim -0.1953125 -12.109375 -0.1953125 -14.2578125 -0.1953125 -16.015625 -0.1953125 -17.96875 -0.1953125 -19.7265625 -0.1953125 -21.484375 -0.1953125 -23.2421875
Last edited by tsitalon1; Jul 15, 2015 at 12:50 PM.
#333
Hello,
I have an EDM evo 8 completely stock (turbo, inj, cams)
I switched to SD (96531706) last week and i have some issues :
1- Over 0.5bar at WOT car run too rich and sometimes had a fuel cut!
2- When lift off after revving (like 15 load ad RPM from 5000 to down 4000) i have 11 AFRMAP and -20*... -20* ok but AFR still 14-16 not 11.
3- lean tip-in...Async Accel vs TPS Delta like yours but nothing changes.
All these things work ok on MAF...and now with SD no!
Your starting setup for RPMVE and MAPVE not working for me...car run too lean at idle like 18 AFR.
Have some advices?
I have an EDM evo 8 completely stock (turbo, inj, cams)
I switched to SD (96531706) last week and i have some issues :
1- Over 0.5bar at WOT car run too rich and sometimes had a fuel cut!
2- When lift off after revving (like 15 load ad RPM from 5000 to down 4000) i have 11 AFRMAP and -20*... -20* ok but AFR still 14-16 not 11.
3- lean tip-in...Async Accel vs TPS Delta like yours but nothing changes.
All these things work ok on MAF...and now with SD no!
Your starting setup for RPMVE and MAPVE not working for me...car run too lean at idle like 18 AFR.
Have some advices?
Last edited by EvilEvolution8; May 14, 2016 at 10:11 AM.
#334
Launch Control ROM 96531706 for JDM Evo 8 mr ( 3 ecu pin )
Hi Evom Fan. I've just add in patch rom 96531706 to my JDM Evo 8 mr ( 3 ecu pin ). Everything goes fine. Smooth running. My problem is now at the Launch Control, seems doesn't work at all even setting in Global Launch map were there. Setting that I made is, Launch Hi Octane Fuel Map , Launch Hi Octane Ignition Map , Launch-Map TPS Threshold : 40% , Launch-Map Speed Threshold : 4 MPH, event I add in -17 retard at Launch Hi Octane Ignition Map from RPM 5250 to 6000 from Load 10 to end map, the Launch still not holding the RPM of 5500. I've tried to search the forum for xml or Hex sample map for me to patch and tyr, but most of the topic discussed without solution. I really need help here.tq
#336
AEM 5 Bar help?
I am trying to get This 5 Bar dialed in and I am having issues. How do I scale this sensor with the Tephra Rom since their is no scaling table? I have the car idling, I just adjusted the RPM VE table so I can move the car in and out of the garage for now. I have done a ton of searching and found the correct scalings but I have no table to scale in this ROM. Would it be easier to just run a basic V7 ROM and add the SD tables and adjust from there?? Help would be appreciated. Thanks
#338
also found this patch posted by mrfred and applied it to my xml file but im not sure if it is correct or the same
<!-- ** Kavlico 5 bar ** -->
<scaling name="MAP 16bit" units="kPa" toexpr="x*0.6320-64.7" frexpr="(x+64.7)/0.6320" format="%.1f" min="0" max="550" inc="0.6320" storagetype="uint16" endian="big"/>
**Edit*** may have this figured out just need to test drive the car.
Last edited by 1UpMoto; Mar 7, 2017 at 02:57 PM.
#339
Guys need some help
I did a E8 ECU conversion in my Evo3 CE9A I have the tephra v7 96530706 with MAF loaded and working fine. But converted to speed density with GM 3 bar Map Sensor and IAT but when I load new map engine wont start, it cranks over but no fire. I have the immobilizer disabled in Pheripary
Any suggestions?
Im using 96533706-TephraMod-l2r99gst-dma-sd BTW
I did a E8 ECU conversion in my Evo3 CE9A I have the tephra v7 96530706 with MAF loaded and working fine. But converted to speed density with GM 3 bar Map Sensor and IAT but when I load new map engine wont start, it cranks over but no fire. I have the immobilizer disabled in Pheripary
Any suggestions?
Im using 96533706-TephraMod-l2r99gst-dma-sd BTW
#340
I'm on ROM 94171715. Omni 4 bar and SD. With the MAP VE table 1:1 and the preset RPM VE Table the car cold starts... warm starts.. and idles great at all temperatures..
take the car out light throttle goes lean out to about 18AFR and then recovers to normal.. at cruise it will do the same and bog the car to a stall until i increase TPS till about 35% then the car jolts forward.. making boost..
when I log LTFT (Low) i get -12.5 across all rpm ranges from 1k-3500... I lowered the MAP VE tables slightly for load values of 31-61 and the idle and start goes berzerk.
I'm searching for some clarity on the RPM and MAP tables. The instructions were lower RPM tables in the lean spots to bring LTFT back to zero?. but then right below there is an EDIT that says lower = less fuel...
car idled great on stock MAF and really drove great.. just wanted to try SD... would changing the injector scaling to a higher number help? Do i need to re-dial in the injectors due to the new intake setup?
take the car out light throttle goes lean out to about 18AFR and then recovers to normal.. at cruise it will do the same and bog the car to a stall until i increase TPS till about 35% then the car jolts forward.. making boost..
when I log LTFT (Low) i get -12.5 across all rpm ranges from 1k-3500... I lowered the MAP VE tables slightly for load values of 31-61 and the idle and start goes berzerk.
I'm searching for some clarity on the RPM and MAP tables. The instructions were lower RPM tables in the lean spots to bring LTFT back to zero?. but then right below there is an EDIT that says lower = less fuel...
car idled great on stock MAF and really drove great.. just wanted to try SD... would changing the injector scaling to a higher number help? Do i need to re-dial in the injectors due to the new intake setup?
Last edited by 03Ev0luti0n; Apr 10, 2017 at 01:54 PM.
#341
03evo -
By the time you will finish reading all 17 pages ,testing and tuning. your issue will be gone.
First page has almost all the things covered which you are asking.
Time to tune ---------------
By the time you will finish reading all 17 pages ,testing and tuning. your issue will be gone.
First page has almost all the things covered which you are asking.
Time to tune ---------------
#344
#345
Does the X axis in the fuel and ignition tables no longer refer to the computer 'load' value in evoscan? When looking at the fuel and ignition tables, I noticed that the unit has changed from 'Engine Load (%)' to 'Engine Load (LOAD kPa)'. When tuning MAF I associated this % load value with the Evoscan load or load2byte column and I'm wondering if I should now be looking at kPa read by the MAP sensor instead.