new and need some help
#16
Newbie
Thread Starter
iTrader: (2)
Join Date: May 2010
Location: ridgeley wv
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
I'll try to uninstall everything tomorrow and reinstall it and see what happens. I dont know if I did something wrong when I installed the open port cable or not but like I said before the only thing I can think of is when the screen came up after plugging in the cable to install it half way through it said something about windows logo not recognize but it seemed to finish to install
#17
Evolved Member
iTrader: (51)
Join Date: Feb 2010
Location: San Antonio
Posts: 1,640
Likes: 0
Received 0 Likes
on
0 Posts
What Windows do you have?
Also, when you uninstall ECUflash make sure you remove it completely. Else you will still have problems with Windows trying to refer back to the old program.
Also, when you uninstall ECUflash make sure you remove it completely. Else you will still have problems with Windows trying to refer back to the old program.
#19
Evolved Member
iTrader: (51)
Join Date: Feb 2010
Location: San Antonio
Posts: 1,640
Likes: 0
Received 0 Likes
on
0 Posts
You should be set as long as you select the proper items. Just a heads up though... you may have to remove EcuFlash a few times and reinstall it. Also, restart your computer after uninstalling EcuFlash.
Keep us updated on what you do so we can help you out.
Keep us updated on what you do so we can help you out.
#20
Newbie
Thread Starter
iTrader: (2)
Join Date: May 2010
Location: ridgeley wv
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Ok so today I uninstalled ecuflash and reinstalled it and I'm still getting the same thing I'm starting to think it's the cable bc of that windows logo error or whatever it is. It's really starting to **** me off
#23
I'll try to uninstall everything tomorrow and reinstall it and see what happens. I dont know if I did something wrong when I installed the open port cable or not but like I said before the only thing I can think of is when the screen came up after plugging in the cable to install it half way through it said something about windows logo not recognize but it seemed to finish to install
http://tactrix.com/index.php?option=...d=36&Itemid=57
That was my problem with similar issues.
#24
This makes me think you need the drivers for the openport found at
http://tactrix.com/index.php?option=...d=36&Itemid=57
That was my problem with similar issues.
http://tactrix.com/index.php?option=...d=36&Itemid=57
That was my problem with similar issues.
Bingo! ^^ Nice guy.
#28
Evolved Member
iTrader: (51)
Join Date: Feb 2010
Location: San Antonio
Posts: 1,640
Likes: 0
Received 0 Likes
on
0 Posts
I didnt even catch that. Your cable needs to be either the 1.3u or 2.0open port to read and write to the Ecu.
Good catch man
Let me find the link so i can post it for verification.
Good catch man
Let me find the link so i can post it for verification.
#29
Evolved Member
iTrader: (51)
Join Date: Feb 2010
Location: San Antonio
Posts: 1,640
Likes: 0
Received 0 Likes
on
0 Posts
Heres the link. Look at the table, 1.3r cables only work in Evoscan...
http://www.evoscan.com/mitsubishi-su...bd2-can-cables
http://www.evoscan.com/mitsubishi-su...bd2-can-cables
#30
step one, install openport driver if need be(i NEVER had too)
step 2 turn your car on and let it idle for about 10-15 mins
step 3, go to your car plug the tactrix cable in (both ports)
step 4 pull EcuFlash up
step 5 select read rom (do NOT turn your car off, EcuFlash will see its on and will turn the car off its self off when trying to read the rom)
step 6.....if the above steps worked its because your voltage on your battery was low and Ecuflash requires at least 12 volts to run (i.e read/write new rom or hex file)
Let me know if it did/didnt work
DO NOT DO THESE IF YOU DO NOT HAVE OPENPORT 1.3u or 2.0 (will brick your ECU)
step 2 turn your car on and let it idle for about 10-15 mins
step 3, go to your car plug the tactrix cable in (both ports)
step 4 pull EcuFlash up
step 5 select read rom (do NOT turn your car off, EcuFlash will see its on and will turn the car off its self off when trying to read the rom)
step 6.....if the above steps worked its because your voltage on your battery was low and Ecuflash requires at least 12 volts to run (i.e read/write new rom or hex file)
Let me know if it did/didnt work
DO NOT DO THESE IF YOU DO NOT HAVE OPENPORT 1.3u or 2.0 (will brick your ECU)
Last edited by blacksunset; Mar 23, 2011 at 12:46 PM.