MAF to SD no start help.
#1
MAF to SD no start help.
OK, let me start: I have a 2001 Evo 7 from the UK-LHD, it did not come with a MAP sensor from the factory. The car has been tuned using the stock MAF and I want to go to Speed Density(SD). I have installed a Omni 4bar MAP into the factory manifold location, while also installing a GM IAT into the upper I/C pipe. Also have a Spoolinup SD EDM/JDM Harness plugged into the MAF harness. My tuner has installed the Tephra v7 ROM and I have switched pin 51 & 92 according to Spoolinup info page.
The problem we are having is the car will try to start but will not. Starts for that 1 sec then dies out(stall) like if the immobilizer is functioning, but it has been disabled. If I put the car back to the way it was, on the stock MAF, it runs just fine. So we are a little confused on what's wrong....
I have tried switching wires (51 & 92) back to stock with SD rom-same thing.
We tried to tweak the SD rom-same thing.
Any help would be greatly appreciated. Willing to pay for the right info that gets the car to start and stay running so we can start the tuning process.
Any questions, please post them so I can answer them here. I want the next person to be able to search and get the answer they need.
Thank you.
The problem we are having is the car will try to start but will not. Starts for that 1 sec then dies out(stall) like if the immobilizer is functioning, but it has been disabled. If I put the car back to the way it was, on the stock MAF, it runs just fine. So we are a little confused on what's wrong....
I have tried switching wires (51 & 92) back to stock with SD rom-same thing.
We tried to tweak the SD rom-same thing.
Any help would be greatly appreciated. Willing to pay for the right info that gets the car to start and stay running so we can start the tuning process.
Any questions, please post them so I can answer them here. I want the next person to be able to search and get the answer they need.
Thank you.
#6
pin 85 - 5.1v
pin 92 - ground
pin 73 - not sure what signal? Reads 0.06v - AH, I see that is suppose to be the MAP sensor signal.....
on the MAF between pin 5 & 6 - 1.82v
testing was done with engine running at idle and with the MAF plugged in and the old rom installed - not with the SD rom in.
.............
Last edited by gvr4v; Jul 12, 2016 at 12:43 PM.
Trending Topics
#8
This is the problem then......my pin 51 is the Immobiliser and my pin 92 is sensor ground.
I'm thinking that the Spoolinup cable can't even be used now....?? I can wire the MAP sensor and the IAT directly to the ECU, but would rather use the Spoolinup cable or make another cable to use with the MAF connector.
Any ideas??
Thank you AUSSIE guys for this great information.
I'm thinking that the Spoolinup cable can't even be used now....?? I can wire the MAP sensor and the IAT directly to the ECU, but would rather use the Spoolinup cable or make another cable to use with the MAF connector.
Any ideas??
Thank you AUSSIE guys for this great information.
#9
Another question: How does the Spoolinup cable get the MAP sensor signal to the ECU? Which pin is it using at the ECU?
AAHHHH: The "MrFred Harness" is the same as the regular SD Harness, but adds an extra foot long harness for Active Baro support through the use of your stock MAP Sensor.
AAHHHH: The "MrFred Harness" is the same as the regular SD Harness, but adds an extra foot long harness for Active Baro support through the use of your stock MAP Sensor.
Last edited by gvr4v; Jul 14, 2016 at 12:49 PM.
#11
Evolving Member
iTrader: (10)
Just a random raaaaaaandom tip. Did you make sure to put in your scaling for your injectors? I was running stock injectors and for some reason thought the tephra maps already had the stock values in (boy was I wrong) they were scaled for around 900cc injectors. Also I would try changing your reading from IAT to the fuel temp sensor to see if that fixes the problem. You can trouble shoot your map from there.
Thread
Thread Starter
Forum
Replies
Last Post
geevolution
Evo Engine / Turbo / Drivetrain
7
Dec 31, 2009 05:31 PM
MitsuJoe
For Sale/WTB - Engine / Drivetrain / Power
1
Aug 27, 2005 07:36 PM