BR builds another, 500+ pump gas, 600+ race gas EVO
#1
BR builds another, 500+ pump gas, 600+ race gas EVO
Just finished up another nice street car build for Josh.
The build:
BR Stage 3, 2 liter
BR Stage 3 head
Cosworth M3 cams
BR Race FMIC
BR upper and lower 2.5" i/c pipes
BR double pumper
PTE 1200cc injectors
BR turbo kit with FP HTA86 turbo
Exedy Triple metallic clutch
BR 3" downpipe
Greddy 3" catback
AEM EMS
Driven Innovations intake manifold
BR 65 mm throttle body
The car was tuned on the fuel it came in here with first, pump gas, unsure of the octane but I assume 93. Peak boost was set to 29 psi.
The car made 570 whp and 409 ft lbs of torque. The torque "curve" is quite impressive in this car. This is one of the first builds we used the Cosworth M3's in and I have to say that the torque is extremely flat both on pump gas and race gas. This build hits 400 ft lbs of torque at 4700 rpm and carries it almost to 8,000 rpm.
Then I turned the boost up to 37 psi and we put the race gas in it.
The power climbed to a best of 654 whp and 527 ft lbs but I was not happy with the curve. I backed the boost and tune down and ended up with the 624 whp/485 ft lb sheet below.
This car is getting delivered a few states away and once it is home I will be working to make more power with it via e-mails and logs. I feel the car has a solid 30-50 more whp in it on race gas for sure. I'd like to see the logs though after it is in it's own "climate" as it was very cold here yesterday and I hate to push it in 20 degree weather when the car will be driven rarely or never in that conditions again.
The car runs great and is smooth as silk. This should be another 9 second EVO for 2009.
Enjoy your car and thanks for letting us build it Josh.
The build:
BR Stage 3, 2 liter
BR Stage 3 head
Cosworth M3 cams
BR Race FMIC
BR upper and lower 2.5" i/c pipes
BR double pumper
PTE 1200cc injectors
BR turbo kit with FP HTA86 turbo
Exedy Triple metallic clutch
BR 3" downpipe
Greddy 3" catback
AEM EMS
Driven Innovations intake manifold
BR 65 mm throttle body
The car was tuned on the fuel it came in here with first, pump gas, unsure of the octane but I assume 93. Peak boost was set to 29 psi.
The car made 570 whp and 409 ft lbs of torque. The torque "curve" is quite impressive in this car. This is one of the first builds we used the Cosworth M3's in and I have to say that the torque is extremely flat both on pump gas and race gas. This build hits 400 ft lbs of torque at 4700 rpm and carries it almost to 8,000 rpm.
Then I turned the boost up to 37 psi and we put the race gas in it.
The power climbed to a best of 654 whp and 527 ft lbs but I was not happy with the curve. I backed the boost and tune down and ended up with the 624 whp/485 ft lb sheet below.
This car is getting delivered a few states away and once it is home I will be working to make more power with it via e-mails and logs. I feel the car has a solid 30-50 more whp in it on race gas for sure. I'd like to see the logs though after it is in it's own "climate" as it was very cold here yesterday and I hate to push it in 20 degree weather when the car will be driven rarely or never in that conditions again.
The car runs great and is smooth as silk. This should be another 9 second EVO for 2009.
Enjoy your car and thanks for letting us build it Josh.
#4
Evolved Member
iTrader: (13)
Join Date: Jan 2006
Location: Las Vegas and HATING it
Posts: 2,916
Likes: 0
Received 1 Like
on
1 Post
When I talked to your boy at SEMA about getting that M3 intake cam for my car I think I am sold on it now over the JUN Cams
Great job on the build, what I like so much about this build is that it is so much like mine with the exception of the turbo and intake cam... Josh has slightly better TQ, but eitherway great job on the build!!!
Have fun Josh
Great job on the build, what I like so much about this build is that it is so much like mine with the exception of the turbo and intake cam... Josh has slightly better TQ, but eitherway great job on the build!!!
Have fun Josh
Trending Topics
#8
Evolving Member
iTrader: (8)
Join Date: May 2006
Location: Atl, Georgia
Posts: 455
Likes: 0
Received 0 Likes
on
0 Posts
Just finished up another nice street car build for Josh.
The build:
BR Stage 3, 2 liter
BR Stage 3 head
Cosworth M3 cams
BR Race FMIC
BR upper and lower 2.5" i/c pipes
BR double pumper
PTE 1200cc injectors
BR turbo kit with FP HTA86 turbo
Exedy Triple metallic clutch
BR 3" downpipe
Greddy 3" catback
AEM EMS
Driven Innovations intake manifold
BR 65 mm throttle body
The car was tuned on the fuel it came in here with first, pump gas, unsure of the octane but I assume 93. Peak boost was set to 29 psi.
The car made 570 whp and 409 ft lbs of torque. The torque "curve" is quite impressive in this car. This is one of the first builds we used the Cosworth M3's in and I have to say that the torque is extremely flat both on pump gas and race gas. This build hits 400 ft lbs of torque at 4700 rpm and carries it almost to 8,000 rpm.
Then I turned the boost up to 37 psi and we put the race gas in it.
The power climbed to a best of 654 whp and 527 ft lbs but I was not happy with the curve. I backed the boost and tune down and ended up with the 624 whp/485 ft lb sheet below.
This car is getting delivered a few states away and once it is home I will be working to make more power with it via e-mails and logs. I feel the car has a solid 30-50 more whp in it on race gas for sure. I'd like to see the logs though after it is in it's own "climate" as it was very cold here yesterday and I hate to push it in 20 degree weather when the car will be driven rarely or never in that conditions again.
The car runs great and is smooth as silk. This should be another 9 second EVO for 2009.
Enjoy your car and thanks for letting us build it Josh.
The build:
BR Stage 3, 2 liter
BR Stage 3 head
Cosworth M3 cams
BR Race FMIC
BR upper and lower 2.5" i/c pipes
BR double pumper
PTE 1200cc injectors
BR turbo kit with FP HTA86 turbo
Exedy Triple metallic clutch
BR 3" downpipe
Greddy 3" catback
AEM EMS
Driven Innovations intake manifold
BR 65 mm throttle body
The car was tuned on the fuel it came in here with first, pump gas, unsure of the octane but I assume 93. Peak boost was set to 29 psi.
The car made 570 whp and 409 ft lbs of torque. The torque "curve" is quite impressive in this car. This is one of the first builds we used the Cosworth M3's in and I have to say that the torque is extremely flat both on pump gas and race gas. This build hits 400 ft lbs of torque at 4700 rpm and carries it almost to 8,000 rpm.
Then I turned the boost up to 37 psi and we put the race gas in it.
The power climbed to a best of 654 whp and 527 ft lbs but I was not happy with the curve. I backed the boost and tune down and ended up with the 624 whp/485 ft lb sheet below.
This car is getting delivered a few states away and once it is home I will be working to make more power with it via e-mails and logs. I feel the car has a solid 30-50 more whp in it on race gas for sure. I'd like to see the logs though after it is in it's own "climate" as it was very cold here yesterday and I hate to push it in 20 degree weather when the car will be driven rarely or never in that conditions again.
The car runs great and is smooth as silk. This should be another 9 second EVO for 2009.
Enjoy your car and thanks for letting us build it Josh.
Thank you so much for everything and thank you to everyone at Buschur Racing. You guys build the sickest cars and I am very happy with the numbers. You guys gave me awesome customer service and took very good care of me. You guys are simply the best. Expect a thread in the review section in the near future
Last edited by WickedIXMR; Feb 20, 2009 at 08:26 AM.
#10
Evolving Member
iTrader: (8)
Join Date: May 2006
Location: Atl, Georgia
Posts: 455
Likes: 0
Received 0 Likes
on
0 Posts
When I talked to your boy at SEMA about getting that M3 intake cam for my car I think I am sold on it now over the JUN Cams
Great job on the build, what I like so much about this build is that it is so much like mine with the exception of the turbo and intake cam... Josh has slightly better TQ, but eitherway great job on the build!!!
Have fun Josh
Great job on the build, what I like so much about this build is that it is so much like mine with the exception of the turbo and intake cam... Josh has slightly better TQ, but eitherway great job on the build!!!
Have fun Josh
No video . And you cant buy the m3 intake cam seperate I already tried Lol
#15
Evolved Member
iTrader: (18)
Join Date: Jun 2005
Location: pittsburgh pa
Posts: 564
Likes: 0
Received 0 Likes
on
0 Posts
Great work again David.
Sick power on a simple setup really , Atlanta has a few fast Buschur cars down there dont they. I think this is the 3rd that I know of , If I remember right. Nick Andy still owns the dyno though bustin out the 700 whp mark haha
Dan
Sick power on a simple setup really , Atlanta has a few fast Buschur cars down there dont they. I think this is the 3rd that I know of , If I remember right. Nick Andy still owns the dyno though bustin out the 700 whp mark haha
Dan