Ported Manifold Dyno Comparison: Buschur vs MAP Rev2
#1
Thread Starter
iTrader: (10)
Ported Manifold Dyno Comparison: Buschur vs MAP Rev2
This is a re-post, just to get the original data back up here. The original thread was deleted because of all the dirt kickers and whiners. If you don't have anything CONSTRUCTIVE to add, please just DON'T BOTHER POSTING.
This is a dyno test comparing the Buschur Ported and ceramic coated stock exhaust manifold and MAP's Rev2 ported stock exhaust manifold.
1) Testing was performed on a Dynojet dynamometer with SAE correction and a smoothing value of 5.
2) Testing was performed in one dyno session over a matter of just a few hours yielding consistent intake air temperatures and negating any environmental factors. The car remained strapped to they dyno while the manifolds were swapped.
3) No changes to the tune were made during testing yielding consistent boost, timing, and AFR's.
4) Standard Buschur and MAP exhaust manifolds were used for this testing, no changes were made and no additional work was performed.
Actual data from actual comparo runs presented above:
Note that my boost numbers are slightly higher than MAP's, since we used different map sensors, and mine was not zero'd out before the test.
Depending on the run, you'll see that the buschur port job nearly equal but slightly out-done by the more extreme MAP port job, but is consistently bested by the MAP manifold above 7000rpm. On average, gains in the midrange were around 4-5whp and up top they were on average 8whp.
Full mod list:
Buschur Racing 3" TBE w/ bullet testpipe
Buschur Racing Intake w/Perrin filter
BR Race FMIC
Custom LICP
BR Upper IC Pipe
OEM IX BOV
AMS/TMS L19 headstuds
MAP Stage 3 Ported Head
Kelford 272 cams
GSC beehive valve springs
BR Ported/Coated Exhaust Mani
CBRD BBK turbo
MAP ported/coated turbine housing
BR SS O2 Housing
BR Ported Intake Manifold w/ EGR delete
BR 65MM TB
Walbro 255HP fuel pump
4x Kracka Vent setup w/ ebay catch-can
Buschur dipstick retention spring
Aquamist HFS-1 Alky Injection Kit (1.0 + .9mm jets)
FIC 1050cc injectors
GM BCS
Evo X MAP sensor
Innovative LC-1
GM IAT
Tephra v7t6 ROM w/EGT Elim, Direct boost mods
Again, if you don't have anything constructive to add, please just don't. These were results of my car, did as scientifically as I could, tried to keep as even as possible. I'm just one guy, with an evo, trying to make it the best it can be with what I have available. Thanks for reading.
This is a dyno test comparing the Buschur Ported and ceramic coated stock exhaust manifold and MAP's Rev2 ported stock exhaust manifold.
1) Testing was performed on a Dynojet dynamometer with SAE correction and a smoothing value of 5.
2) Testing was performed in one dyno session over a matter of just a few hours yielding consistent intake air temperatures and negating any environmental factors. The car remained strapped to they dyno while the manifolds were swapped.
3) No changes to the tune were made during testing yielding consistent boost, timing, and AFR's.
4) Standard Buschur and MAP exhaust manifolds were used for this testing, no changes were made and no additional work was performed.
Actual data from actual comparo runs presented above:
Note that my boost numbers are slightly higher than MAP's, since we used different map sensors, and mine was not zero'd out before the test.
Depending on the run, you'll see that the buschur port job nearly equal but slightly out-done by the more extreme MAP port job, but is consistently bested by the MAP manifold above 7000rpm. On average, gains in the midrange were around 4-5whp and up top they were on average 8whp.
Full mod list:
Buschur Racing 3" TBE w/ bullet testpipe
Buschur Racing Intake w/Perrin filter
BR Race FMIC
Custom LICP
BR Upper IC Pipe
OEM IX BOV
AMS/TMS L19 headstuds
MAP Stage 3 Ported Head
Kelford 272 cams
GSC beehive valve springs
BR Ported/Coated Exhaust Mani
CBRD BBK turbo
MAP ported/coated turbine housing
BR SS O2 Housing
BR Ported Intake Manifold w/ EGR delete
BR 65MM TB
Walbro 255HP fuel pump
4x Kracka Vent setup w/ ebay catch-can
Buschur dipstick retention spring
Aquamist HFS-1 Alky Injection Kit (1.0 + .9mm jets)
FIC 1050cc injectors
GM BCS
Evo X MAP sensor
Innovative LC-1
GM IAT
Tephra v7t6 ROM w/EGT Elim, Direct boost mods
Again, if you don't have anything constructive to add, please just don't. These were results of my car, did as scientifically as I could, tried to keep as even as possible. I'm just one guy, with an evo, trying to make it the best it can be with what I have available. Thanks for reading.
Last edited by scheides; Dec 8, 2009 at 12:00 PM.
#6
Evolved Member
iTrader: (20)
Join Date: Jul 2007
Location: Gator Nation(UF)
Posts: 1,453
Likes: 0
Received 0 Likes
on
0 Posts
Nice gains, looks like the exhaust manifold can be ported a bit more it seems. look like its spooling a bit quicker too with the REV2, can anyone confirm? I can't really see much with all the colors.
Trending Topics
#10
Evolved Member
iTrader: (1)
Join Date: Mar 2007
Location: moss beach, ca
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
do you happen to have stock mani data on that car? if not, no biggie, i have seen the stock vs rev2/rev 3 data from map.
in any event, makes sense to get the map mani. thanks for posting the data!
in any event, makes sense to get the map mani. thanks for posting the data!
#14
Evolved Member
iTrader: (6)
Join Date: Sep 2005
Location: NYC
Posts: 2,269
Likes: 0
Received 0 Likes
on
0 Posts
Nice test man!
Am i reading it corectly on the excel graphs? It seems that the Map manifold spikes just a tiny bit higher and it runs just a tiny bit leaner. Would this be the reason for the increased power?
Since the tune remained unchanged for both manifolds, what the higher boost and leaner afrs mean? Deeper porting? Larger porting?
Is it possible to have average hp from both manifolds? In other words what's the average hp difference let's say from 2500rpm to 7500rpm?
Am i reading it corectly on the excel graphs? It seems that the Map manifold spikes just a tiny bit higher and it runs just a tiny bit leaner. Would this be the reason for the increased power?
Since the tune remained unchanged for both manifolds, what the higher boost and leaner afrs mean? Deeper porting? Larger porting?
Is it possible to have average hp from both manifolds? In other words what's the average hp difference let's say from 2500rpm to 7500rpm?