View Poll Results: greddy type s - how many springs ?
stock - two springs
40
34.48%
mod - single spring
76
65.52%
Voters: 116. You may not vote on this poll
poll: greddy type s - two stock springs or single spring mod
#31
Evolving Member
I know how to make your type s vent to atmosphere without any stalling... if anyone is interested... It sonds very good, a huge whistle, and it is very loud.
(I got a ticket because the cop thought i spun my tires, when all i did was rev up and blow off if that tells u nething)
(I got a ticket because the cop thought i spun my tires, when all i did was rev up and blow off if that tells u nething)
#32
Evolving Member
iTrader: (10)
Join Date: May 2004
Location: Bay Area, CA
Posts: 350
Likes: 0
Received 0 Likes
on
0 Posts
I am running mines on VTA too without stalling problems. I plan to convert it back to recirculating though... noise is getting a bit too much to take plus i felt like i got better response when i had it on recirculating
#33
Evolving Member
iTrader: (7)
Join Date: Sep 2004
Location: Naples, FL
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
? for you guys.
does your type s sound like a bash of air then the ping sound? i get a whosh-ping noise everytime. i am recirculating and it is loud so vta is out of the question.
does your type s sound like a bash of air then the ping sound? i get a whosh-ping noise everytime. i am recirculating and it is loud so vta is out of the question.
#35
Evolved Member
iTrader: (38)
On the pictures I posted on the second page, you can see the smaller secondary nipple just to the right of the main one (to the right in this picture). It is on the same side of the piston as the main line (the intake side).
In the picture on the first page of this thread, the secondary nipple is on the "bolt-on" flange, on the other side of the piston from the main line (the IC pipe side). At least that is what my eyes are seeing.
What's up with that? Anyone else see this?
EVOlutionary
In the picture on the first page of this thread, the secondary nipple is on the "bolt-on" flange, on the other side of the piston from the main line (the IC pipe side). At least that is what my eyes are seeing.
What's up with that? Anyone else see this?
EVOlutionary
#36
Evolving Member
iTrader: (11)
Join Date: Mar 2003
Location: N/A
Posts: 129
Likes: 0
Received 0 Likes
on
0 Posts
Does anyone know where to connect the secondary nipple (Vacuum?) to? i have mine not connected to anything and left it open to air. I think that connecting it would cure my fluttering problem.
#37
Originally Posted by PiNG
Does anyone know where to connect the secondary nipple (Vacuum?) to? i have mine not connected to anything and left it open to air. I think that connecting it would cure my fluttering problem.
#38
Evolving Member
iTrader: (11)
Join Date: Mar 2003
Location: N/A
Posts: 129
Likes: 0
Received 0 Likes
on
0 Posts
mine's set as 2 springs, and about 5 turns after the contact point for the hardening and softening setting, i used to have it how you set up on the picture in the first posts, but it fluttered pretty hard, and my current setting is light flutters about 1 sec long.
u think that's fine? how does yours sound? High boost, it's no problem, no fluttering, but there's pretty long wistling sound at the end of the WOOSH. it holds boost no problem.
u think that's fine? how does yours sound? High boost, it's no problem, no fluttering, but there's pretty long wistling sound at the end of the WOOSH. it holds boost no problem.
#40
Evolving Member
iTrader: (11)
Join Date: Mar 2003
Location: N/A
Posts: 129
Likes: 0
Received 0 Likes
on
0 Posts
yup, the car, but totally forgot to take a look at your bov, but i did play around with it today (2 posts up) , and ended up with that result, seems to be better, i'll keep adjusting and see what i get, but current setup dosn't flutter as much as how i had it on saturday.
#41
Evolved Member
iTrader: (12)
Join Date: Aug 2004
Location: MA
Posts: 1,249
Likes: 0
Received 0 Likes
on
0 Posts
I must be lucky, I installed mine on Friday night and I havent had any issues at all. I got the RRE version, but I dont have the hose connected from the two tips. I will try it with that to see if its different.... I have mine turned about 2/3 turns.
#44
Newbie
iTrader: (1)
Join Date: Mar 2005
Location: tWIN CITY
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
got the single in there with screw turned about 2 to 3.
just dont get it? noticed more leak (chirping noise at idle and when driving) when screw is turned in more!
no matter what, I still have a leak!
I'm thinking about just going with MR BOV. EVO drives fine but I sure would love to eliminate the noise! I havent tried installing both springs yet! my last option before I go get MR BOV!!
just dont get it? noticed more leak (chirping noise at idle and when driving) when screw is turned in more!
no matter what, I still have a leak!
I'm thinking about just going with MR BOV. EVO drives fine but I sure would love to eliminate the noise! I havent tried installing both springs yet! my last option before I go get MR BOV!!
#45
Evolved Member
iTrader: (6)
Join Date: May 2004
Location: San Antonio, TX.
Posts: 510
Likes: 0
Received 0 Likes
on
0 Posts
Ok, I'm waiting on my type-s in the mail... whats the true verdict?
With my mods..and running 21-23lbs daily..what to do? Single spring (large one) or what? I'm getting so confused..lol
With my mods..and running 21-23lbs daily..what to do? Single spring (large one) or what? I'm getting so confused..lol