EvolutionM - Mitsubishi Lancer and Lancer Evolution Community

Notices
Evo Engine / Turbo / Drivetrain Everything from engine management to the best clutch and flywheel.

how to install zeitronix zt2?

Thread Tools
 
Search this Thread
 
Old Dec 17, 2005, 09:26 AM
  #61  
Account Disabled
iTrader: (465)
 
TTP Engineering's Avatar
 
Join Date: May 2005
Location: Central FL
Posts: 8,824
Likes: 0
Received 2 Likes on 2 Posts
I say you have those 2 connections reversed.
TTP Engineering is offline  
Reply Like
Old Jan 8, 2006, 02:12 AM
  #62  
Newbie
Thread Starter
 
lagcisco's Avatar
 
Join Date: Mar 2005
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
I installed the boost sensor today but it reads boost as negative?

then goes into positive when I boost up..

is it ok to install the sensor inside the engine bay?

I didnt want to run the vacum line inside the cockpit
lagcisco is offline  
Reply Like
Old Jan 8, 2006, 02:30 AM
  #63  
Evolved Member
iTrader: (8)
 
AznFlip's Avatar
 
Join Date: Aug 2003
Location: Seattle
Posts: 2,808
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by lagcisco
I installed the boost sensor today but it reads boost as negative?

then goes into positive when I boost up..

is it ok to install the sensor inside the engine bay?

I didnt want to run the vacum line inside the cockpit
all boost sensor/gauge does that.
AznFlip is offline  
Reply Like
Old Jan 8, 2006, 02:41 AM
  #64  
Evolved Member
iTrader: (12)
 
trinydex's Avatar
 
Join Date: Jan 2004
Location: not here
Posts: 6,072
Likes: 0
Received 7 Likes on 6 Posts
Originally Posted by lagcisco
I installed the boost sensor today but it reads boost as negative?

then goes into positive when I boost up..

is it ok to install the sensor inside the engine bay?

I didnt want to run the vacum line inside the cockpit
this is known as vacuum. the car runs in vacuum around idle. this is becuase the movement of the pistons "sucks" air through the engine. only when you're boosting is air "crammed" in and pressure goes up.
trinydex is offline  
Reply Like
Old Jan 8, 2006, 02:52 AM
  #65  
Newbie
Thread Starter
 
lagcisco's Avatar
 
Join Date: Mar 2005
Posts: 80
Likes: 0
Received 0 Likes on 0 Posts
hey trinydex are you on socalevo by any chance? you're from LA right?

you answer alot of my questions

thanks.
lagcisco is offline  
Reply Like
Old Jan 8, 2006, 03:22 AM
  #66  
Evolved Member
iTrader: (12)
 
trinydex's Avatar
 
Join Date: Jan 2004
Location: not here
Posts: 6,072
Likes: 0
Received 7 Likes on 6 Posts
yeah i am... but this forum gets so much more action... so i only go to socal every like few days. all the homies is there tho
trinydex is offline  
Reply Like
Old Mar 24, 2006, 03:30 PM
  #67  
Evolved Member
iTrader: (12)
 
trinydex's Avatar
 
Join Date: Jan 2004
Location: not here
Posts: 6,072
Likes: 0
Received 7 Likes on 6 Posts
[QUOTE=TTP Engineering]
Originally Posted by AznFlip
Can somone complete and correct this.

Zt-2 Pin #..............ECU Pin #

1........................25 YES
2............................ IN YOUR CASE, NOT USED.
3............................58 YES
4.....WITHOUT BOOST SENSOR= NOT USED -OUTPUT FROM BOOST SENSOR ORANGE
6............................81 YES
7............................26 YES
8............................92 THAT IS FINE
9............................... NOT USED
10..........................84 YES
11............................. WITHOUT BOOST SENSOR= NOT USED, WITH SENSOR=92
12............................. NOT USED IN STANDARD INSTALLATION
for 11 can you also make the boost sensor's black wire come in here?
trinydex is offline  
Reply Like
Old Mar 24, 2006, 03:59 PM
  #68  
Account Disabled
iTrader: (465)
 
TTP Engineering's Avatar
 
Join Date: May 2005
Location: Central FL
Posts: 8,824
Likes: 0
Received 2 Likes on 2 Posts
Originally Posted by trinydex
for 11 can you also make the boost sensor's black wire come in here?
Yes, sensor ground 92.
TTP Engineering is offline  
Reply Like
Old Mar 26, 2006, 12:40 PM
  #69  
Evolved Member
iTrader: (12)
 
trinydex's Avatar
 
Join Date: Jan 2004
Location: not here
Posts: 6,072
Likes: 0
Received 7 Likes on 6 Posts
when installing hte safc the ground wires go in a certain order. when installing the zeitronix also... is there a similar order or a prefered order of ground wiring?
trinydex is offline  
Reply Like
Old Mar 27, 2006, 06:55 AM
  #70  
Account Disabled
iTrader: (465)
 
TTP Engineering's Avatar
 
Join Date: May 2005
Location: Central FL
Posts: 8,824
Likes: 0
Received 2 Likes on 2 Posts
There is no order because the grounds do not go to the same place. Ecu gnd and sensor gnd are two different pins.
TTP Engineering is offline  
Reply Like
Old Mar 27, 2006, 08:38 AM
  #71  
Evolved Member
iTrader: (12)
 
trinydex's Avatar
 
Join Date: Jan 2004
Location: not here
Posts: 6,072
Likes: 0
Received 7 Likes on 6 Posts
ok cool... do you happen to know why the safc has preference for ground? the brown wire has to be closer to the ecu? i'm just curious now.
trinydex is offline  
Reply Like
Old Jun 20, 2006, 03:33 PM
  #72  
Evolved Member
iTrader: (44)
 
justchil's Avatar
 
Join Date: Oct 2003
Location: Charleston, WV
Posts: 4,409
Likes: 0
Received 0 Likes on 0 Posts
This thread was usefull for my install My zt2 only came with instructions for the warning box not for the main unit (unless I somehow lost them). Now if the screen came with a mounting bracket I'd be golden
justchil is offline  
Reply Like
Old Jul 22, 2006, 11:48 AM
  #73  
Evolved Member
iTrader: (6)
 
nj1266's Avatar
 
Join Date: Nov 2004
Location: USA
Posts: 3,254
Likes: 0
Received 13 Likes on 3 Posts
Originally Posted by lagcisco
I installed the boost sensor today but it reads boost as negative?

then goes into positive when I boost up..

is it ok to install the sensor inside the engine bay?

I didnt want to run the vacum line inside the cockpit
Do you happen to have a boost log from your Zeitronix? Can you post it in *.csv or *.dif format?
nj1266 is offline  
Reply Like
Old Jul 22, 2006, 12:01 PM
  #74  
Account Disabled
iTrader: (465)
 
TTP Engineering's Avatar
 
Join Date: May 2005
Location: Central FL
Posts: 8,824
Likes: 0
Received 2 Likes on 2 Posts
Originally Posted by nj1266
Do you happen to have a boost log from your Zeitronix? Can you post it in *.csv or *.dif format?
His post was from over 7 months ago. The ZEITRONIX medical grade precision kavlico 3.5bar MAP sensor reads in both vacuum and boost.
TTP Engineering is offline  
Reply Like
Old Dec 1, 2006, 07:31 PM
  #75  
Evolving Member
iTrader: (22)
 
LimPShoT's Avatar
 
Join Date: Jul 2005
Location: Oregon
Posts: 334
Likes: 0
Received 0 Likes on 0 Posts
Bringing this one back. Helped me alot on my install but was wondering where the Purple wire goes (pin 9) from zeitronix harness??
LimPShoT is offline  
Reply Like



Advanced Search
Quick Reply: how to install zeitronix zt2?


Reply Closed Thread Share

All times are GMT -7. The time now is 11:59 PM.