High-energy grounding cable kit
Apr 28, 2003, 06:57 PM
#31
Newbie
Join Date: Mar 2003
Location: Vivid Racing in AZ
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
we have Lineage grounding kits as well as the Hot Earth. the Lineage kit is made from 4 gauge wire and has crimped then soldered for a solid connection. they retail for $119, we sell them for $99. they smooth out acceleration and add at least 5hp. plus, your power accesories run better under power.
Jun 9, 2003, 04:51 PM
#32
Newbie
iTrader: (1)
Join Date: Jun 2003
Location: Somewhere in the 3rd dimension
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
Just installed mitsu's hypergrounding system ($189.00); did the install myself in about one hour and throttle response is much greater, idle's smoothly and is quicker in transition on freeway. Seat-of-the-pants dyno guesstamates 5-6 hp and similar torque. Good investment now waiting forRMR downpipe and cat-back to arrive.
Jun 9, 2003, 05:16 PM
#33
Newbie
Join Date: Dec 2002
Location: Los Angeles, CA
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by purecoda
Oxygen-free audio cable is supposed to be an ultra-low resistance cable used for audio system installs. Its a bit more expensive but MUCH higher quality than hardware store wire. It is also often shielded, as to not allow as much noise interference into your audio system.
Oxygen-free audio cable is supposed to be an ultra-low resistance cable used for audio system installs. Its a bit more expensive but MUCH higher quality than hardware store wire. It is also often shielded, as to not allow as much noise interference into your audio system.
To me, as long as the cable is thick enough, the quality shouldn't matter too much. I would assume that all problems come from the contact points. As long as there isn't too much surface oxidation, I would say it should work fine. But then again, I'm not an engineer.
Jun 9, 2003, 07:23 PM
#35
Evolved Member
iTrader: (2)
Join Date: May 2002
Location: Jamaica.
Posts: 719
Likes: 0
Received 0 Likes
on
0 Posts
Hi Articfury, what ODBII probe/software are you using to capture this data?
Originally posted by articfury
Here is the screenshot from the same car with the grounding kit installed:
Here is the screenshot from the same car with the grounding kit installed:
Jun 9, 2003, 07:52 PM
#36
Evolving Member
iTrader: (38)
Join Date: Sep 2002
Location: Staten Island
Posts: 458
Likes: 0
Received 0 Likes
on
0 Posts
I just finished installing my HKS earthing kit and damn I've noticed a difference esspecially in the cars idle. When I would be at a complete stop at a traffic light the cars steering wheel used to shake a lot more than it shakes now that the earthing kit is on. I'm super pleased with the results, and installation was extremely easy concidering the instructions were entirely in Japanese. I improvised.
Jun 10, 2003, 01:51 AM
#37
Newbie
iTrader: (1)
Join Date: Apr 2003
Location: Texas
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
jemm-
It is not my setup.
A member at my350z.com did the test. He bought it at http://www.obd-2.com .
I hope that helps.
D
It is not my setup.
A member at my350z.com did the test. He bought it at http://www.obd-2.com .
I hope that helps.
D
Thread
Thread Starter
Forum
Replies
Last Post
