My Zex Nitrous setup
#4
Evolved Member
Join Date: Mar 2006
Location: new york
Posts: 2,669
Likes: 0
Received 0 Likes
on
0 Posts
that time is horrible for juice
there are stock 9 going 12.9
correct me if i am wrong am i missing something?with a boost controler,tbe,intake and a tune you could be in the 11's...
why cause all this stress on your motor if u dont have to?
there are stock 9 going 12.9
correct me if i am wrong am i missing something?with a boost controler,tbe,intake and a tune you could be in the 11's...
why cause all this stress on your motor if u dont have to?
Last edited by bluebyu36; Oct 30, 2007 at 04:45 PM.
Trending Topics
#10
like i sayd if i had a bottle heater and a full bottle i would of pulled a 11 no problem but with no nitrous and no heater its mostly just spraying fuel. as for my times on no bottle it was 13.3 with a 1.8 60 ft. the times at my elevation are higher because iv been running at Bandimere in Denver Colorado witch= no oxygen. ya i have a aem wideband and with the 75 shot it never got over 10 so its way rich! i did the nitrous because it works amaizing on turbo cars ,it makes for hardly no lag and i will be getting meth as well i would like to run both.
#11
Account Disabled
iTrader: (122)
Join Date: Apr 2005
Location: Peekskill NY
Posts: 6,876
Likes: 0
Received 0 Likes
on
0 Posts
Keep us updated, get back to track with the bottle full and make sure you dial in your afrs you will pick up a lot of power just from tuning the jets properly...on our shop cobra we went from making 70whp to 130whp by adjusting the fuel jet properly...
#12
Evolved Member
iTrader: (66)
As soon as my twin disk goes in... so does nitrous. I've had it on all of my previous cars and even a truck.
I am curious how you tapped into your fuel line. Did you just snip it and install a "Y" fitting or did you get the plug and play fitting?
What jets are you using? On my DSM I ran a 46/26 combo which ended up being more than advertised at the wheels.
Back then I was using DSMLink to control the spray. Controlling the on portion is the only thing I haven't sorted out for the EVO. I don't want to flip a switch midway down the track and I can't use an RPM window switch or it will engage during the stutterbox. I may end up just running it out of the hole and launching at a lower RPM. What do you do?
I am curious how you tapped into your fuel line. Did you just snip it and install a "Y" fitting or did you get the plug and play fitting?
What jets are you using? On my DSM I ran a 46/26 combo which ended up being more than advertised at the wheels.
Back then I was using DSMLink to control the spray. Controlling the on portion is the only thing I haven't sorted out for the EVO. I don't want to flip a switch midway down the track and I can't use an RPM window switch or it will engage during the stutterbox. I may end up just running it out of the hole and launching at a lower RPM. What do you do?
#15
Evolved Member
iTrader: (7)
Join Date: Nov 2006
Location: Pittsburgh
Posts: 772
Likes: 0
Received 0 Likes
on
0 Posts
I went 12.6 with a few basic bolt ons.
If I ran 12.70 with nitrous. I'd walk off a short pier.
Get the bottle filled and a proper tune.
It should be night/day difference.
If I ran 12.70 with nitrous. I'd walk off a short pier.
Get the bottle filled and a proper tune.
It should be night/day difference.
Last edited by Asmodeus6; Oct 31, 2007 at 08:26 AM.