mdosu

iTrader: (6)

Evo 9 Gurney Flap only...

Rich@Orbital

iTrader: (16)

Unfortunately, that conversion won't work. It's electronic and our systems are manual.

After a TON of R&D and prototype development, I finally released a kit that will make your USDM dash a true 2-DIN.

See here:

https://www.evolutionm.net/forums/sh...d.php?t=194844

https://www.evolutionm.net/forums/sh...d.php?t=214986

https://www.evolutionm.net/forums/sh...d.php?t=214747

Rich@Orbital

iTrader: (16)

Does anyone have a P/N for the retention clips that clip onto the radio/climate bezel on the dash?

VIIImylunch

iTrader: (6)

Does anyone now what part this is, it is off an exedy twin disk clutch. I am not sure if its OEM or an exedy piece.

sonicnofadz

iTrader: (4)

There are six 8mm little nuts that hold the fuel pump housing onto the fuel tank. I managed to lose a few of mine. What is the part number for these?

bigballz

iTrader: (1)

Anyone know what part this is? MN180105?? Got into a fender bender and this part looks bent. Its on the right front side, right infront of the plastic thing. Looks like a black mini-raditor or something.

sonicnofadz

iTrader: (4)

Probably the oil cooler.

Knightr

iTrader: (12)

Well changing my pads from a cough cough track event... looks like one of the PINS and the CLIP flew out of the caliper..

does any one know where you can buy the replcaement PINS and the CLIP..

they go thru the caliper and the clip holds the pads in... i'm sure if you have seen your calipers you know what i'm talking about. I have all my stock stuff back on now and want to drive it but with one Rear missing it's one pin and the clip not going to.

I need to find a part number and either have the dealer order couple rear kits, and one front. (might as well have some spares..)

my car is stock but funny thing is even though it blows away porsche's and M3's and stuff you would think the Brembo's wouldn't turn into BrownBo's so damn fast... i have a freind with 78K on his Porsche.... still look almost new like the day he got them... i think they used CHEAP paint on the EVO's....

either way i love this car way better than my 330ci was now i just need to get the brake parts to get it back on the road.

thanks everyone

edtxag

iTrader: (5)

if i was going to order the rear seats from an evo ix for my car what part numbers would i have to ask for? doubt they just sell the fabric covers.....that would be to easy

DruMMinStUd06

iTrader: (17)

is there any difference between these two part numbers? im tryin to find out which oil filter to order for my IX MR...

Md356000

Mz690116

DruMMinStUd06

iTrader: (17)

well, with a 30% discount i believe its $1800 just for the rear seat butt cushion. i dont know about you guys...but i dont pamper my rear that much.

Spins4

iTrader: (122)

You want the MZ690116 ..and don't forget MD050317 (drain plug washer).

webguy330i

iTrader: (17)

the seat covers should be separate, they are after all separate parts. =)

MBaran

iTrader: (2)

on the topic of parts lookup, what is the newest CAPS that anyone on the forum has?
Im running 3.41 which seems to cover 05 MR's?

Thanks.

DruMMinStUd06

iTrader: (17)

just the washer or the plug also?