Tuning the Profec B spec II--simple version
#47
Evolving Member
iTrader: (35)
here are my settings:
low:
set 50%
gain 5%
set gain 20
warning 70
warning limiter 10%
hi:
set 100%
gain 5%
set gain 40
warning 75
warning limiter 10%
i have a tial external wastegate with a 7psi spring. my top boost was 10.8 psi.
i think i need to adjust a few things. i want my low to be about 4-5 psi and high to be like 8 or so. that way i can change from fuel economy to race mode.
low:
set 50%
gain 5%
set gain 20
warning 70
warning limiter 10%
hi:
set 100%
gain 5%
set gain 40
warning 75
warning limiter 10%
i have a tial external wastegate with a 7psi spring. my top boost was 10.8 psi.
i think i need to adjust a few things. i want my low to be about 4-5 psi and high to be like 8 or so. that way i can change from fuel economy to race mode.
In any case, I have no idea if/when my Profec's solenoid clicks - my Evo is so loud, I probably couldn't hear the solenoid making any noises even if it was mounted on top of my dash.
#48
Evolved Member
iTrader: (19)
Join Date: May 2007
Location: South Central WI
Posts: 1,620
Likes: 0
Received 0 Likes
on
0 Posts
If you're exceeding your desired high boost level by 2.8 psi, I'd guess you need to back down the set percentage and/or the set gain.
Clicking? There's no mechanical components inside of the Profec controller to make any noises... are you saying you're hearing the solenoid all the way from the engine compartment, while driving?
In any case, I have no idea if/when my Profec's solenoid clicks - my Evo is so loud, I probably couldn't hear the solenoid making any noises even if it was mounted on top of my dash.
Clicking? There's no mechanical components inside of the Profec controller to make any noises... are you saying you're hearing the solenoid all the way from the engine compartment, while driving?
In any case, I have no idea if/when my Profec's solenoid clicks - my Evo is so loud, I probably couldn't hear the solenoid making any noises even if it was mounted on top of my dash.
thanks i will look into that. as for the "clicking" i found here on the forum that it is a normal thing and not to worry about it.
should i lower both the set ans the set gain on both high and low?
josh
#49
Evolved Member
iTrader: (19)
Join Date: May 2007
Location: South Central WI
Posts: 1,620
Likes: 0
Received 0 Likes
on
0 Posts
current:
low...
set 50%
gain 5%
set gain 20
warning 70
w. limiter 10%
high...
set 100%
gain 5%
set gain 40
warning 75
w. limiter 10%
i think...
if i lower my set on the low side to 40% and my set gain to 10, and on the high side my set to 75% and set gain to 30, my boost should go down.
if anyone wants to take a crak at it here is the manual from greddy.
http://www.greddy.com/img/PHP/products/pdf/682.pdf
josh
ok so with the above info that i "adjusted" today to the values, i hit a 13.3 psi on high!
then i had some bov flutter, and found out that i had melted the vacuum line from the bov to the fpr had melted!
josh
#50
Evolving Member
Join Date: Feb 2009
Location: USA , CAL
Posts: 115
Likes: 0
Received 0 Likes
on
0 Posts
#53
EvoM Community Team Leader
iTrader: (60)
so many pages.. has anyone asked?
i am getting 21-18-21-18-21psi.
my settings:
gain: 52%
gain: 5%
setgain: 150 (15psi)
warning: 230 (23psi). trying to reach 21psi in 3rd gear.
warning L: 15%
peak boost was: 214 (21.4psi).
it's acting like it's hitting the warning level, though peak is clearly lower. any ideas??
i am getting 21-18-21-18-21psi.
my settings:
gain: 52%
gain: 5%
setgain: 150 (15psi)
warning: 230 (23psi). trying to reach 21psi in 3rd gear.
warning L: 15%
peak boost was: 214 (21.4psi).
it's acting like it's hitting the warning level, though peak is clearly lower. any ideas??
#56
EvoM Community Team Leader
iTrader: (60)
1. i have the stock setup. instructions said to run "com" to turbo and "no" to wastegate actuator.
i DOUBLE checked the lines.. maybe i'm crazy.. but i had them that way and the more i'd increase SET, the lower boost i'd run. WTF??
so.. i swapped them. now it works.
2. as for the solenoid clicking, i found it was 'cause i started my GAIN and SET GAIN at 0. well.. duh.. with SET GAIN at 0, the solenoid is working as soon as boost starts. that's why my solenoid was clicking.
is it your solenoid that's clicking?
#57
EvoM Community Team Leader
iTrader: (60)
a few things i've noticed in this thread:
i'd say the 15% gain setting is causing your boost spike. your bar > psi is messing me up. LOL.
your start boost is set at 2.0 psi. so, your wastegate is opening REALLY early. can you hear the solenoid clicking at low boost? do you suffer from slow spool?
I have an Evo 8 and i'm tuned for 24 psi. I had it locked at 22psi when I was tuned for it. Been a bit of an uphill batle trying to get it to stay at 24psi.
My settings are:
set: 68
start boost: 20
gain: 6
limiter: .4
warning: 250
Takes a bit to get it right. Any ideas?
My settings are:
set: 68
start boost: 20
gain: 6
limiter: .4
warning: 250
Takes a bit to get it right. Any ideas?
Thread
Thread Starter
Forum
Replies
Last Post
FS[Northeast]: 2003 Evo, Reliable Daily Driver (Ohio)
EVO TYME!
For Sale - Cars For Sale
3
Oct 24, 2014 07:14 PM
Jimbolution
Evo Engine / Turbo / Drivetrain
6
Jun 3, 2009 05:28 AM
Freddy302
Evo Engine / Turbo / Drivetrain
76
Sep 20, 2007 10:19 AM