Hallman boost controller in stock SALE!
#31
Originally Posted by turbo4g63
So it feels much better when you hook that hose to the bov vaccum hose? I hooked it up the way Al told me, but it drops from 20psi to 18psi when I WOT on 3rd gear.
As for your boost drop in 3rd, I would recheck all the upper I/C pipe clamps including the BOV clamps. I read a thread about the stock BOV clamp being very loose from the factory and when I checked mine, it sure was. I could practically pull my BOV out of the piping. I would loosen all the clamps and make sure they have a sure fit on each pipe and retighten them all. If you have upgraded pipes, I suppose that could be another factor for the boost drop.
Another thing to look at is to make sure there isn't a leak in the vacume hose for your boost gauge. Where did you tap into for the vacume? I ran mine from the vacume off the throttle body because it makes the most sense to read the boost off the point closest to where it enters the engine.
These are just theories of mine. For an expert diagnosis, I would consult Al.
#32
Evolved Member
iTrader: (9)
Join Date: Feb 2003
Location: Alexandria, VA
Posts: 1,520
Likes: 0
Received 0 Likes
on
0 Posts
these are also available through the online store at http://store.dynoflash.com
Just enter the coupon "dragwin" during checkout for 5.00/off with free shipping through thursday
Just enter the coupon "dragwin" during checkout for 5.00/off with free shipping through thursday
Last edited by nastea; Jun 22, 2004 at 12:52 PM.
#33
Evolving Member
iTrader: (4)
Join Date: Sep 2003
Location: Virginia, US
Posts: 177
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Ken8masters
My goes from the BOV to the HBC to the wastgate. Exactly like the diagram that Mitsuorder posted on reply #23. I spoke to Al last night and he clarified a few things for me and told me my HBC is operating exactly like it's suppose to. I'm very satisfied with my HBC and don't plan on replacing it.
As for your boost drop in 3rd, I would recheck all the upper I/C pipe clamps including the BOV clamps. I read a thread about the stock BOV clamp being very loose from the factory and when I checked mine, it sure was. I could practically pull my BOV out of the piping. I would loosen all the clamps and make sure they have a sure fit on each pipe and retighten them all. If you have upgraded pipes, I suppose that could be another factor for the boost drop.
Another thing to look at is to make sure there isn't a leak in the vacume hose for your boost gauge. Where did you tap into for the vacume? I ran mine from the vacume off the throttle body because it makes the most sense to read the boost off the point closest to where it enters the engine.
These are just theories of mine. For an expert diagnosis, I would consult Al.
As for your boost drop in 3rd, I would recheck all the upper I/C pipe clamps including the BOV clamps. I read a thread about the stock BOV clamp being very loose from the factory and when I checked mine, it sure was. I could practically pull my BOV out of the piping. I would loosen all the clamps and make sure they have a sure fit on each pipe and retighten them all. If you have upgraded pipes, I suppose that could be another factor for the boost drop.
Another thing to look at is to make sure there isn't a leak in the vacume hose for your boost gauge. Where did you tap into for the vacume? I ran mine from the vacume off the throttle body because it makes the most sense to read the boost off the point closest to where it enters the engine.
These are just theories of mine. For an expert diagnosis, I would consult Al.
Last edited by turbo4g63; Jun 23, 2004 at 07:57 AM.
#38
Originally Posted by turbo4g63
Mitsuorder posted on reply #23 is from the turbo housing to HBC then to the wastegate. # 24 is from BOV to the HBC then to the wastegate. Which method you really use that is hold rock solid? I used method #24.
#43
Account Disabled
Thread Starter
iTrader: (91)
Join Date: Sep 2003
Location: 2003 Evo VIII - Silver
Posts: 16,850
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Mevolution2002
Awesome deal but im having a problem with the website. I typed in the coupon code and only got free shipping and not the $5 off??
The sale is now over
Regular pricing is in effect and we have plenty of black and red in stock and ready to ship in the pro and the evolution pro
#45
Account Disabled
Thread Starter
iTrader: (91)
Join Date: Sep 2003
Location: 2003 Evo VIII - Silver
Posts: 16,850
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mitsuorder
so Al which method of installation of the mbc do you prefer?