Official "Apex Silver" Picture Thread
Mar 11, 2013, 01:30 PM
#3306
Evolving Member
iTrader: (4)
Join Date: Apr 2008
Location: Philly
Posts: 102
Likes: 0
Received 0 Likes
on
0 Posts
Here is an older dirty pic of my car... now sits lower and has more carbon goodness 
My Mods are the following...
4G64 2.4LR Build:
*Engine Internals*
-Manley 10:1 comp. Platinum Series Coated LR spec Pistons
-Manley Turbo Tuff 156mm Rods
-ARP head, rod, and main studs/bolts
-ACL Race Rod and Crank bearings
-Manley SS 1mm oversized valves
-Manley Stg. 3 Dual Valve-Springs w/ Titanium Retainers
-Cosworth 272 M2 Cams
-Stg. 1 Head porting
*Engine External*
-SpoolinUp C.O.P. Kit
-Self Ported Intake Mani. W/ P2R gasket
-Full Blown 70mm Throttle Body
-STM EGR block off plate
-AEM adj. cam gears
-Gates Kevlar Racing T-Belt & A/C delete drive belt
-Balance Shaft removal kit
-New OEM oil pump, water pump, and tensioner
-Buscher modified Oil Pan w/race baffling
-Greddy Oil Catch Can
*Turbo Set-Up*
-Forced Performance HTA3586R w/ Garret 1.06a/r Twin-Scroll T4 hot side
-DNP SS Tubular T4 Twin-Scroll Manifold
-44mm Tial Wastegate w/ custom dumptube
-Custom 3" Downpipe w/ test pipe
-AMS Race FMIC w/ 4" Core w/ 2.5" IC piping
-Synapse BOV
-DEI Titanium exhaust wrap on manifold, dp, & dumptube
-LavaShield Turbo Blanket
-Custom 4" Intake w/ 9" K&N filter
*Fuel &Tuning Set-Up*
-1680cc Bosch Injectors
-E85 400lph+ Walboro Pump
-AEM Adj. Fuel Pressure Regulator w/ B&M gauge
-AEM Fuel Rail
-MAP 6AN SS fuel return line setup w/ STM adapter
-4Bar Omni MAP sensor
-SpoolinUp Speed Density conversion harness w/ IAT sensor
-Tephra version 7 w/ Speed Density
-AEM wideband, Autometer Boost & Oil pressure gauges
*Transmission & Driveline*
-Shep Stg2 Trans
-QuarterMaster 8-Leg Race version clutch w/ hydraulic release bearing
-TRE 12 plate Rear Diff
-Redline Fluids throughout
-Whiteline Rear Diff bushings
-STM Solid trans bushings
-ACD-Tuning Custom maps for track & auto-x
*Suspension & Brakes*
-Stance SS 15-Way Adj. Coilovers
-Hotchkis 24mm Adj Rear Sway-Bar
-Whiteline Roll Center Ball-Joints& Tie-Rods
-Custom 3"-2" brake ducting w/ Binary caliper adapters
-DBA 4000 Rotors front and rear
-EBC Red pads front and rear
-All SS Brake Lines w/ ATE Super Blue fluid
-18x9.5 Enkei NT03-M et27 in gunmetal w/10mm front spacers
-275/35-18 Toyo RA1s
*Aerodynamics*
-APR GTC-300 67" CF Spoiler
-APR CF Front Splitter (heavily reinforced)
-APR CF Canards (x4)
-APR Rear Diffuser
-DoLuck Front Spoiler/lip
-Rexpeed CF front air ducts
-Rexpeed Painted Vortex Generator
-Rexpeed CF Side Spats
-Rexpeed CF Bumper Exhaust Shield
My Mods are the following...
4G64 2.4LR Build:
*Engine Internals*
-Manley 10:1 comp. Platinum Series Coated LR spec Pistons
-Manley Turbo Tuff 156mm Rods
-ARP head, rod, and main studs/bolts
-ACL Race Rod and Crank bearings
-Manley SS 1mm oversized valves
-Manley Stg. 3 Dual Valve-Springs w/ Titanium Retainers
-Cosworth 272 M2 Cams
-Stg. 1 Head porting
*Engine External*
-SpoolinUp C.O.P. Kit
-Self Ported Intake Mani. W/ P2R gasket
-Full Blown 70mm Throttle Body
-STM EGR block off plate
-AEM adj. cam gears
-Gates Kevlar Racing T-Belt & A/C delete drive belt
-Balance Shaft removal kit
-New OEM oil pump, water pump, and tensioner
-Buscher modified Oil Pan w/race baffling
-Greddy Oil Catch Can
*Turbo Set-Up*
-Forced Performance HTA3586R w/ Garret 1.06a/r Twin-Scroll T4 hot side
-DNP SS Tubular T4 Twin-Scroll Manifold
-44mm Tial Wastegate w/ custom dumptube
-Custom 3" Downpipe w/ test pipe
-AMS Race FMIC w/ 4" Core w/ 2.5" IC piping
-Synapse BOV
-DEI Titanium exhaust wrap on manifold, dp, & dumptube
-LavaShield Turbo Blanket
-Custom 4" Intake w/ 9" K&N filter
*Fuel &Tuning Set-Up*
-1680cc Bosch Injectors
-E85 400lph+ Walboro Pump
-AEM Adj. Fuel Pressure Regulator w/ B&M gauge
-AEM Fuel Rail
-MAP 6AN SS fuel return line setup w/ STM adapter
-4Bar Omni MAP sensor
-SpoolinUp Speed Density conversion harness w/ IAT sensor
-Tephra version 7 w/ Speed Density
-AEM wideband, Autometer Boost & Oil pressure gauges
*Transmission & Driveline*
-Shep Stg2 Trans
-QuarterMaster 8-Leg Race version clutch w/ hydraulic release bearing
-TRE 12 plate Rear Diff
-Redline Fluids throughout
-Whiteline Rear Diff bushings
-STM Solid trans bushings
-ACD-Tuning Custom maps for track & auto-x
*Suspension & Brakes*
-Stance SS 15-Way Adj. Coilovers
-Hotchkis 24mm Adj Rear Sway-Bar
-Whiteline Roll Center Ball-Joints& Tie-Rods
-Custom 3"-2" brake ducting w/ Binary caliper adapters
-DBA 4000 Rotors front and rear
-EBC Red pads front and rear
-All SS Brake Lines w/ ATE Super Blue fluid
-18x9.5 Enkei NT03-M et27 in gunmetal w/10mm front spacers
-275/35-18 Toyo RA1s
*Aerodynamics*
-APR GTC-300 67" CF Spoiler
-APR CF Front Splitter (heavily reinforced)
-APR CF Canards (x4)
-APR Rear Diffuser
-DoLuck Front Spoiler/lip
-Rexpeed CF front air ducts
-Rexpeed Painted Vortex Generator
-Rexpeed CF Side Spats
-Rexpeed CF Bumper Exhaust Shield
Mar 13, 2013, 01:51 AM
#3315
Evolving Member
