Will regular spray paint hold up if layered with high heat paint on valve cover??
#1
Fomer Vendor
Thread Starter
iTrader: (18)
Join Date: Sep 2003
Location: Central FL
Posts: 1,154
Likes: 0
Received 0 Likes
on
0 Posts
Will regular spray paint hold up if layered with high heat paint on valve cover??
So I want to paint my valve cover, and I am big on DIY, so I want to do it myself. It will save some money when compared to powder coating too.
But my question is, would regular spray paint (states "do not exceed 200°"; I checked VC temps, they are +-200° depending on location) hold up if layered with high heat spray paint?
For example: 1) High heat primer, 2) Regular spray paint, 3) High heat clear.
I think it should work. If regular spray paint is sandwiched between high heat spray paint, it, in my theory, should hold up. I want to buy the paint and test it on some spare sheet metal I have, but I want some logical opinions before I spend my money.
Another reason for trying to use regular spray paint is that with the high heat stuff it is pretty limited on color and style. Also, right now this is just an idea, I may not even paint it if I can't find a color I like. I found a couple of colors that may work, they look good on the top of the can, but that is small and not in my engine.
But my question is, would regular spray paint (states "do not exceed 200°"; I checked VC temps, they are +-200° depending on location) hold up if layered with high heat spray paint?
For example: 1) High heat primer, 2) Regular spray paint, 3) High heat clear.
I think it should work. If regular spray paint is sandwiched between high heat spray paint, it, in my theory, should hold up. I want to buy the paint and test it on some spare sheet metal I have, but I want some logical opinions before I spend my money.
Another reason for trying to use regular spray paint is that with the high heat stuff it is pretty limited on color and style. Also, right now this is just an idea, I may not even paint it if I can't find a color I like. I found a couple of colors that may work, they look good on the top of the can, but that is small and not in my engine.
#4
Evolved Member
iTrader: (19)
Kerr, I took the same route that you mentioned back in high school on a friend's Integra valve cover (not as hot as ours probably) and it held up great until he sold the car years later. I even did a Jun-style fade on it. For better odds, use high quality paints like Rust-Oleum brand or sub-brands (Painters touch, American Accents etc.) If it looks like crap down the road, oh well just polish or powercoat it. Powdercoating is pretty cheap on a valve cover BTW.
#6
Fomer Vendor
Thread Starter
iTrader: (18)
Join Date: Sep 2003
Location: Central FL
Posts: 1,154
Likes: 0
Received 0 Likes
on
0 Posts
Hokiruu, thanks for the input, thanks everyone. I am going to weigh all my options, just trying to figure out is I can rattle can it. I need to find a color I like first.
Trending Topics
#9
Fomer Vendor
Thread Starter
iTrader: (18)
Join Date: Sep 2003
Location: Central FL
Posts: 1,154
Likes: 0
Received 0 Likes
on
0 Posts
I know high heat will work, I believe the cover gets just over 200 degrees. That temp is the max temp for normal paint, so my question was if the normal paint would hold up if layered with high heat paint.
#10
Evolving Member
iTrader: (4)
im not 100% sure if that would work. since you are just putting a few layers between, i would think that once the 1st layer hits that temp , the other layer (reg. paint) will start to fade. I put regular paint on my 2g Eclipse Manifold, it was white and blue. but started to fade and turn brownish.