New Aquamist HFS-6 group buy ends in 1st March
#1
Former Sponsor
Thread Starter
iTrader: (5)
Join Date: Aug 2005
Location: England
Posts: 2,236
Likes: 0
Received 0 Likes
on
0 Posts
New Aquamist HFS-6 group buy ends in 1st March
GB list is up
(ends in 1st March)
please click here to register (you may need to sign in first)
(Answer to anti-spam question: methanol)
Closed
Last edited by Richard L; Mar 1, 2009 at 03:18 AM.
#5
Former Sponsor
Thread Starter
iTrader: (5)
Join Date: Aug 2005
Location: England
Posts: 2,236
Likes: 0
Received 0 Likes
on
0 Posts
The kit does not come with a tank. A good tank source is US plastic Corp, about $12.00, caps sold separately (~$3.00).
We don't have the image yet but here is an illustration of the entire system:
(except the water tank- NOT supplied)
Last edited by Richard L; Feb 22, 2009 at 03:11 PM.
#6
Evolving Member
iTrader: (10)
Join Date: May 2006
Location: Tampa Area
Posts: 465
Likes: 0
Received 0 Likes
on
0 Posts
ok....I will be adding myself to that list tomorrow.
1 more question. I noticed in the drawing of the system that it shows 1 meth jet. Will you be able to run 2 jets like the preivous setups.
1 more question. I noticed in the drawing of the system that it shows 1 meth jet. Will you be able to run 2 jets like the preivous setups.
Trending Topics
#8
Former Sponsor
Thread Starter
iTrader: (5)
Join Date: Aug 2005
Location: England
Posts: 2,236
Likes: 0
Received 0 Likes
on
0 Posts
Quick summary of the functions of the HFS-6's main control panel
Jumper links (default):
- System is triggered by Fuel IDC % (second from left)
- Spare jumper link is in parked position
- Water injection is enabled. Unlink for "dry-run" test
Three onboard LEDs
- Green LED: Fuel idc detection. Grow brighter as IDC increases
- Amber LED: The trigger point is reached, water injection commences
- Red LED: The water injection has almost reached its full flow.
Potentiometers to manipulate the flow curve.
(Adjustment is optional - preset at 12 o'clock)
- THRES ADJ: Set triggering point to start injection. Default: 42% IDC
- IDC TRIM: Add or subtract IDC% from the starting point. Default: IDC-in = IDC-out
- IDC gain: Alter ramp rate of the IDC-out relative to the IDC-in Default: 1:1 ratio.
- BOOST COMP: Increase the flow to offset the manifold pressure. Default: 2.5V
- FLSF SENS: Failsafe sensitivity/response to over or under flow spikes. Default: 400mS
- FLSF RST: Failsafe reset time after trigger. Default: 3 seconds
- DIM ADJ: Gauge brightness for night driving: Default: 50%
#12
Former Sponsor
Thread Starter
iTrader: (5)
Join Date: Aug 2005
Location: England
Posts: 2,236
Likes: 0
Received 0 Likes
on
0 Posts
The gauge is 52 mm.
I have found a few old pictures of the gauges. EXcept for the mixture up of blue and red led on the "water injection on" . Red bargraph should have red "Water injection on" led
I have found a few old pictures of the gauges. EXcept for the mixture up of blue and red led on the "water injection on" . Red bargraph should have red "Water injection on" led
Last edited by Richard L; Feb 24, 2009 at 06:01 AM.