Notices
Lancer Troubleshooting Get help with any troubleshooting problems you may have.

New exhaust on 2003 OZ

Thread Tools
 
Search this Thread
 
Old Jan 26, 2010, 10:09 AM
  #16  
Newbie
iTrader: (1)
 
IdahoRally's Avatar
 
Join Date: Jan 2010
Location: Orofino, Idaho
Posts: 21
Likes: 0
Received 0 Likes on 0 Posts
Honestly the N1 "JDM" Catback on ebay is not a bad unit at all. My car has seen many ebay parts, and so far I have been satisfied with the catback completely. It was easy to install, took my dad and I under an hour and a half and after pulling the silencer off it sounded great. It definitely has a deeper sound then you would expect, not to loud, but loud enough. Though, be wary that if you have a CAI it will be extremely loud (This is the same with any unit though) Mine was so loud it forced me to take off the air unit.
Old May 14, 2010, 01:32 PM
  #17  
Newbie
 
mikediamond84's Avatar
 
Join Date: Jul 2009
Location: Washington State
Posts: 51
Likes: 0
Received 0 Likes on 0 Posts
N1 off ebay and headers will be ok? not too loud?
Old May 14, 2010, 04:39 PM
  #18  
Evolving Member
iTrader: (4)
 
Onkar02's Avatar
 
Join Date: Jun 2007
Location: Tracy Ca
Posts: 258
Likes: 0
Received 0 Likes on 0 Posts
Greddy ti-c FTW
Old May 14, 2010, 05:35 PM
  #19  
Evolved Member
iTrader: (7)
 
ambystom01's Avatar
 
Join Date: Sep 2003
Location: Canuckistan
Posts: 15,634
Likes: 0
Received 75 Likes on 68 Posts
Ti-C if you want loud as ****, .
Old May 15, 2010, 06:45 AM
  #20  
Evolving Member
 
cedes14bamg's Avatar
 
Join Date: May 2009
Location: New Brunswick, Canada
Posts: 161
Likes: 0
Received 0 Likes on 0 Posts
just go at a muffler shop and make them do a custom exhaust.
i have 2.25 piping from the cat to the rear, and a nice 2.5 inlet 3 inch outlet muffler welded on.
i find it ridiculous to pay high *** **** for a name brand exhaust...
piping is piping, of course stainless steel or galvenized pipes are more expensive but i have alluminized pipes and its lighter and didnt cost me an arm.
and mendrel bent is useless...
Old May 15, 2010, 09:26 AM
  #21  
Evolved Member
iTrader: (7)
 
ambystom01's Avatar
 
Join Date: Sep 2003
Location: Canuckistan
Posts: 15,634
Likes: 0
Received 75 Likes on 68 Posts
Mandrel bent means it's a true 2.25/2.5/3" exhaust all the way back.
Old May 15, 2010, 07:03 PM
  #22  
Evolving Member
iTrader: (2)
 
zbailey129's Avatar
 
Join Date: Feb 2008
Location: Indiana
Posts: 177
Likes: 0
Received 0 Likes on 0 Posts
I have had the Greddy Evo 2 exhaust on my car since 2004 and it has a nice deep tone. It has gotten a bit louder over the years, but not loud enough to set off car alarms. The piping is 60mm with a 115mm tip.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Racecarzz08
Lancer Engine Tech
19
Jun 13, 2023 03:35 AM
Cameron Barlow
Lancer Engine Tech
0
Nov 12, 2016 11:21 AM
xbenbendx
04-06 Ralliart General
30
Mar 14, 2013 10:39 AM
Horus
Vendor Service / Parts / Tuning Review
28
Oct 29, 2012 03:19 PM
TommiM
Evo General
10
Aug 30, 2009 12:05 PM



Quick Reply: New exhaust on 2003 OZ



All times are GMT -7. The time now is 03:52 PM.