2003 Caged BBY Evo 8
For Sale2003 Mitsubishi Lancer Evolution
-
Price
$25,000• OBO • Trade
- Location Commerce Township, MI, 48382, USA
- Condition Used
- VIN JA3AH86F93U124075
- Mileage 89,000
- Engine 4 cyl
- Drive Type AWD
- Transmission Manual
- Vehicle Type Sedan
- Exterior Color Blue
Description:
General Info:
2003 Mitsubishi Evolution
Caged Interior w/ Race Seats + Harnesses
~89k miles
Clean Michigan Title In Hand
VIN: JA3AH86F93U124075
Asking: $25k for everything or best offer.
I’ve owned this vehicle for ~2 years and have fully gone through it at this point. The vehicle operates as intended obviously with the focus being on Track. The vehicle was recently re-tuned w/ Speed Density purposely keeping the calibration ~330awtq for longevity on Track.
All functions work on the vehicle including AC. Vehicle runs fantastic; I wouldn’t hesitate to daily drive this (if it wasn’t caged) or drive it long distance (I’ve driven this to and from tracks occasionally). All leaks have been corrected while I went through the vehicle. It has been garage kept for the majority of its life so it’s very clean inside and out.
I have a ton of spare parts/fluids/consumables to go with the vehicle as noted below.
Please let me know if you have any questions and I can provide any videos / data logs upon request.
Images:
Evo_Images
Engine / Drivetrain
· Pump 93 Speed Density Tune by Jay at BoostedTuning
. Blouch Evo 9 Dominator 1.0XTR Turbo (Ball Bearing)
· Swain Tech White Lightning-coated JM Fab EVO Twin Scroll Exhaust Manifold,
· Injector Dynamics 1065cc injectors (p/n 1050.60.11.D.4)
· GSC S2 cams,
· Ported + Swain Tech White Lightning-coated OEM intake manifold,
· MIL.SPEC 65mm throttle body,
· AMS Intercooler,
· AMS lower intercooler pipe,
· Samco intercooler hoses,
· ETS upper intercooler pipe,
· STM intake & cone filter,
· Cajun Powers's t-bolt clamp kit,
· Evo 9 metal BOV,
· Kiggly Racing 4G63 HLA Pressure Regulator
· Grimspeed 3Port EBCS
. Spoolin’ Up Speed Density Harness w/ GM IAT + 4 Bar MAP
· Invidia O2 housing,
· Perrin 3 inch Downpipe (Jet Hot 2000 coated),
· Cat-delete test pipe,
· Fujitsubo RA-01 exhaust,
· TRE Transfer Case Rebuild w/ Ralliart LSD,
· ACT HDSS clutch kit,
· ACT Street Lite flywheel,
· TRE Stage 2 Transmission w/ Evo 9 1st gear,
. Setrab Engine Oil Cooler
. Racefab Oil Pan
. APR Headstuds
Wheels / Tires
- Enkei RPF1 17x8.5 +30 w/ conti extreme contact force 200tw 255/40/17, used 80% tread left
- Enkei pf01 18x9.5 w/ Sticker RE71RS 255/35/18
Suspension
· Cusco Titanium Front Strut Tower Brace,
· Perrin PSRS Front Lower Control Arm bushings,
· WORKS Urethane Bushing Kit (Front Anti-sway Bar, Front Lower Control Arm, Rear Bump Steer, Rear Upper Control Arm, Rear Lower Control Arm Forward + Rearward, Rear Trailing Arm),
· Whiteline Rollcenter Adjustment kit
- White line Rear Sway bar
· Cusco camber plates (front) Piro Ball 564 410 A
· Cusco rear strut mounts
· WORKS Racing Program Rear Pillow Ball Mounts,
· Perrin Rear Sway Bar Endlinks,
· Perrin Front Lower Control Arm Brace,
· AMS Moustache Bar Eliminator Kit,
· AMS lightweight Front Crossmember.
Interior / Exterior
· Rennessy Fabrication custom Carbon Fiber Sunroof plug,
· eBay urethane lower bumper lip,
· Mitsubishi MR Rear Vortex Generator,
· Rennessy Fabrication 6 point roll cage,
· Racetech 4009W seats & mounts w/ Buddy Club Racing Seat Sliders,
· Schroth Enduro 6 point harness (driver) and Profi II 6 point harness (passenger),
· Beatrush Rear Bulkhead Panel,
· XPEL Headlight / Sideview Mirror Film,
· Black/White Gauge Overlay package,
· Defi 60mm Boost/EGT/Oil Pressure gauges (plus Oil Temp gauge to replace Oil Pressure)
. AEM X Series AFR Gauge w/ analog out
· Defi Dashboard Gauge Pod,
· Defi Link II Control Unit,
· OEM Carbon Fiber E-Brake Handle,
· AMS Shift Knob,
· Momo Racing Mod. 78 steering wheel,
· NRG 2.5 Quick-Release Steering Hub,
· All-View Race Mirror,
· Mitsubishi Blue Racing Pedal Kit
Recent Maintenance (Most were done pre-re-tune to have a trouble free experience):
- Throttle Body Shaft Seals
- Throttle Body Gasket (Grimmspeed)
- Exhaust Manifold to head, Exhaust manifold to turbo, turbo to O2 housing gaskets
- Primary O2 Sensor Replaced
- Low Pressure Fuel Pump (Walbro 255, done pre-retune just because)
- New Set of Spark Plugs, gapped to .022”
- All fluids have been changed (Engine Oil / Transfer Case / Rear Diff / Transmission / Brake Fluid) recently with Mobil1/Redline/Mobul products.
- New OEM Intake Air Control Valve
- New Ferodo front and rear pads (5/19)
- AC clutch
- Recently replaced drivers side inward axle boot; there is still some residual grease (it’s hard to get it all)
- Drivers rear wheel bearing w/ Timken Bearing
***FLUIDS***
Several bottles of Mobil1 Engine Oil and Motul Trans Fluid
Partial can x Mitsubishi Diaqueen SAE90 LSD gear oil
7 x Mitsubishi MZ690116 oil filter
4 x Mobil 1 M1-108 oil filter
3 x Hawk Performance hi-temp brake grease packets
**Brakes**
1 x AP Racing front rotor set (new) 1901912(LH) & 1901913(RH) 1.25x12.81 J-hook, hardware inc.
2 x Ferodo front pad sets (new) FRP3116Z
2 x Hawk rear pad sets in Hawk HP Plus front pad box (likely HP Plus)
1 x rear pad sets (used) in Ferodo box 1 x front pad set (used in Ferodo box
**Spark Plugs**
2 x NGK Iridium 4-pack BPR7EIX #4055
***Stock Parts***
Mits Evo floor mats
Rear seat bench & back
Rear seat back bolts
Trunk floor
Strut tower brace
sunroof glass
BBY front lip
1 x intake & exhaust cams
4 x stock fuel injectors
1 x Exhaust header nut MR224500
1 x PCV valve MD152772
1 x bolt right rear suspension MB856459
1 x Kart Boy urethane exhaust hangar bushing
2 x splash clips MB547806
1 x 10pc splash clip MB547806
1 x fr brake shim set (one caliper) MR475618
2 x engine bay fuse covers (1 lrg, 1 narrow)
1 x oil pan drain plug
1 x (used) rear fender liner hardware
1 x brake bleeder rubber caps 3pc MR407368
8 x eng ro clip 1pc MU488006
10 x retaining clip MR288150
unmarked clips inc 4 x phillip head clips, 2 x hex head bolts
1 x radiator cap
1 x o2 sensor MN153010, used
1 x used shifter bushings, washers, cotter pins
2 x stock rubber pedal covers (clutch, brake) removed for OEM blue cover kit
1 x stock alternator pulley
1 x stock HLA presure regulator
1 x stock cam sensor cover
***Aftermarket parts***
NRG QuickLock for QuickRelease - SRK-101LS (2 keys)
APR front splitter w/ chassis mount hardware
Aluminum plug for rear wiper delete
1 x Airtek Idle Air Control valve 2H1076 (new, Rock Auto)
1 x Kicks magnetic drain plug M14xP1.5 (blue)
1 x Greddy radiator cap Type S GRC-13S
1 x Titek magnetic drain plug M14x1.50 blue
3 x Schroth adjusting grips (6pt belts) P/N00092
1 x Schroth elastic band kit P/N 00050
1 x set Precision Injected 1000cc low impedance injectors (used)
1 x set HKS 272 cams 22002-AM003,-AM004 (used ~30k mi)
Things to note:
- DEFI Oil Pressure gauge is dead. Unit is unplugged. I have an engine oil temp gauge to go in it’s place that will be included.
- EGT sensor is not installed as there was a leak in that location on the manifold; had to re-tap it and plug it. Didn’t want to create another potential leak location while car was going to get fixed/tuned.
- Front pinch welds are flat. Rears are still in the correct position. I use a hockey puck to jack there if I need to and use flat top jack stands.
