Sup w/them 2024 Summer Projects?
#5132
EvoM Guru
iTrader: (1)
Originally Posted by RazorLab
Okay. I was going to offer to help tune it but I haven't worked with the FreeFuel rom on the 9. Only 8 and Tephra 10.
#5133
Evolved Member
iTrader: (34)
Yes and no. I've had a lot of success back in the day tuning Evo 8 roms. Evo 9 I've struggled with more even with the same tephra version. I noticed some prominent tuners (at the time) even stuck with older tephra versions for Evo 9. Not sure the current state of affairs.
#5134
EvoM Guru
iTrader: (1)
Originally Posted by deeman101
Yes and no. I've had a lot of success back in the day tuning Evo 8 roms. Evo 9 I've struggled with more even with the same tephra version. I noticed some prominent tuners (at the time) even stuck with older tephra versions for Evo 9. Not sure the current state of affairs.
What I was saying is that If you can tune a 9, and you can tune a flex 8, you can tune a flex 9.
#5135
EvoM Guru
iTrader: (2)
separate note, for the guys running harnesses on roll bars, did you guys just weld a loop on for the harness to pass through?
i was looking at this solution (https://rennscot.com/products/rspro-...31783378190474) which i think is intriguing - easy to install/remove, quick and easy solution. not sure if people will scoff at a locking collar to hold the harness in place for side-to-side motion, but some don't use anything at all?
i was looking at this solution (https://rennscot.com/products/rspro-...31783378190474) which i think is intriguing - easy to install/remove, quick and easy solution. not sure if people will scoff at a locking collar to hold the harness in place for side-to-side motion, but some don't use anything at all?
#5136
Evolved Member
iTrader: (2)
We just put them around the bar and zip tie the tail. That looks like a nice product.
separate note, for the guys running harnesses on roll bars, did you guys just weld a loop on for the harness to pass through?
i was looking at this solution (https://rennscot.com/products/rspro-...31783378190474) which i think is intriguing - easy to install/remove, quick and easy solution. not sure if people will scoff at a locking collar to hold the harness in place for side-to-side motion, but some don't use anything at all?
i was looking at this solution (https://rennscot.com/products/rspro-...31783378190474) which i think is intriguing - easy to install/remove, quick and easy solution. not sure if people will scoff at a locking collar to hold the harness in place for side-to-side motion, but some don't use anything at all?
#5137
Evolved Member
iTrader: (29)
The following 2 users liked this post by RSMike:
alpinaturbo (Feb 27, 2023),
ViciousLSD (Feb 25, 2023)
#5139
EvoM Guru
iTrader: (1)
"Winter" projects - ENDLESS Brakes
ENDLESS 6POT kit with 345x32mm 2-piece discs.
Old PFC 2-piece discs are 7.75kg (17lbs) per assembly. ENDLESS is 8.2kg (18lbs) per assembly.
Adding disc weight is critical for brake performance. The heavier the better.
The piston sizing is slightly smaller than the OEM Brembo calipers, so this keeps the brake balance the same (or very close to) OEM specs with the increase in disc diameter size.
ENDLESS disc has a 19mm airgap with 72 vanes. PFC was 18mm airgap with 48 vanes.
I've gone with CCRg compound for now, we'll see how they go on the track. I've got another set of ENDLESS ME20 to swap over if needed.
ENDLESS RF650 brake fluid too.
They fit under my ADVAN TC4, RG3 and WedsSport TC105X. All 17" models.
ENDLESS 6POT kit with 345x32mm 2-piece discs.
Old PFC 2-piece discs are 7.75kg (17lbs) per assembly. ENDLESS is 8.2kg (18lbs) per assembly.
Adding disc weight is critical for brake performance. The heavier the better.
The piston sizing is slightly smaller than the OEM Brembo calipers, so this keeps the brake balance the same (or very close to) OEM specs with the increase in disc diameter size.
ENDLESS disc has a 19mm airgap with 72 vanes. PFC was 18mm airgap with 48 vanes.
I've gone with CCRg compound for now, we'll see how they go on the track. I've got another set of ENDLESS ME20 to swap over if needed.
ENDLESS RF650 brake fluid too.
They fit under my ADVAN TC4, RG3 and WedsSport TC105X. All 17" models.
The following users liked this post:
alpinaturbo (Feb 27, 2023)
#5140
EvoM Guru
separate note, for the guys running harnesses on roll bars, did you guys just weld a loop on for the harness to pass through?
i was looking at this solution (https://rennscot.com/products/rspro-...31783378190474) which i think is intriguing - easy to install/remove, quick and easy solution. not sure if people will scoff at a locking collar to hold the harness in place for side-to-side motion, but some don't use anything at all?
i was looking at this solution (https://rennscot.com/products/rspro-...31783378190474) which i think is intriguing - easy to install/remove, quick and easy solution. not sure if people will scoff at a locking collar to hold the harness in place for side-to-side motion, but some don't use anything at all?
I just have some little hoops welded onto the horizontal bar on my cage. they are probably 7mm profile? maybe 5? they look sort of like a cheap kitchen cupboard door handle lol. Then roll the tail up and tie off with cable tie.
#5142
EvoM Guru
https://alemlube.com.au/web/product/...c-c12ab9b0e4ed
They work good you can just climb under and pump away. has measurements on the side so you can see how much has gone in. doesnt leak if u lie it on its side etc.
#5143
EvoM Guru
iTrader: (2)
maybe you can drop this drum pump in a smaller container
https://www.ebay.com/itm/385392209937
I may try it one of these days
https://www.ebay.com/itm/385392209937
I may try it one of these days
#5144
Evolved Member
iTrader: (2)
I use one of these. It's still manual but at least you don't need to get the pump primed and screw around with 800 pumps while laying on the ground. you just put the fluid you want in it and smash it in.
https://a.co/d/5YlT776
https://a.co/d/5YlT776