Worcester/Boston Social Thread
Evolving Member
Thread Starter
iTrader: (7)
Join Date: Jun 2007
Location: Northborough, MA
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
EvoM Staff Alumni
iTrader: (16)
Kristen should be up and to work early tomorrow. I would like to try to be at your place by 9ish if that works. It really depends if i wake up but i dont see a problem getting up at 8 and heading over.
I tired to buy some speed bleeders for our install tomorrow but they dont sell them anywhere anymore.
I tired to buy some speed bleeders for our install tomorrow but they dont sell them anywhere anymore.
Evolved Member
iTrader: (13)
Join Date: Sep 2004
Location: Marlboro, MA
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
Kristen should be up and to work early tomorrow. I would like to try to be at your place by 9ish if that works. It really depends if i wake up but i dont see a problem getting up at 8 and heading over.
I tired to buy some speed bleeders for our install tomorrow but they dont sell them anywhere anymore.
I tired to buy some speed bleeders for our install tomorrow but they dont sell them anywhere anymore.
Will we be able to effectively use my power bleeder?
9's fine with me....it should be warm enough, but I may get a fire going in there in the morning anyhoo.
EvoM Staff Alumni
iTrader: (16)
The power bleeder should be fine.
I figure i can head over early and we can figure out a game plan while any fire needs to be started. I doubt we would start promptly at 9.
I scoped out the clutch line last night too. It shouldn't be too bad but getting to the master cylinder is going to be a pita to take the line off and put back on. Otherwise should be cake.
Evolved Member
iTrader: (13)
Join Date: Sep 2004
Location: Marlboro, MA
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
So they are a lot smaller then the normal brake bleeder and Help! used to make them but no one carries them anymore, i know, i called around. I got quite annoyed.
The power bleeder should be fine.
I figure i can head over early and we can figure out a game plan while any fire needs to be started. I doubt we would start promptly at 9.
I scoped out the clutch line last night too. It shouldn't be too bad but getting to the master cylinder is going to be a pita to take the line off and put back on. Otherwise should be cake.
The power bleeder should be fine.
I figure i can head over early and we can figure out a game plan while any fire needs to be started. I doubt we would start promptly at 9.
I scoped out the clutch line last night too. It shouldn't be too bad but getting to the master cylinder is going to be a pita to take the line off and put back on. Otherwise should be cake.
UICP and battery? Turbo inlet and filter, too?
Evolving Member
Thread Starter
iTrader: (7)
Join Date: Jun 2007
Location: Northborough, MA
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
i dig the rear wing on this: https://www.evolutionm.net/forums/sh...d.php?t=315766
otherwise its a little overdone tho imo
otherwise its a little overdone tho imo
EvoM Staff Alumni
iTrader: (16)
Evolved Member
iTrader: (13)
Join Date: Sep 2004
Location: Marlboro, MA
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
YAY!
Evolved Member
iTrader: (13)
Join Date: Sep 2004
Location: Marlboro, MA
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
i dig the rear wing on this: https://www.evolutionm.net/forums/sh...d.php?t=315766
otherwise its a little overdone tho imo
otherwise its a little overdone tho imo
except for the gas tank badge (WTFBBQ?) and the stickers and shist on the side, it's really nice lookin. I dig it.
Evolved Member
iTrader: (13)
Join Date: Sep 2004
Location: Marlboro, MA
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
Ooops. Lemme call back!
EDIT: I had the right part number.
EDIT, again: He is "nearly positive that there's 2 in a package" but it's not specified...he ordered two SKUs in case they're singly packed but I didn't have to prepay for them so he'll just send a package back if they are paired up. Long story short, we're all good.
I'm super psyched for tomorrow!!!
Last edited by avengerhed; Mar 28, 2008 at 08:05 AM.
Evolving Member
Thread Starter
iTrader: (7)
Join Date: Jun 2007
Location: Northborough, MA
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
i usually don't like CF trunks, but i think it works well with the all CF wing.
i'm also not a fan of the rain gaurds on the windows or whatever they are called.
EDIT: i dont wanna know how much that wign costs...
Last edited by Paulnsx; Mar 28, 2008 at 08:28 AM.
Evolved Member
iTrader: (13)
Join Date: Sep 2004
Location: Marlboro, MA
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
yeah thats pretty much what i meant. too much with the sticks and the gas tank badge. it would look a little better with the SE lip + splitter too.
i usually don't like CF trunks, but i think it works well with the all CF wing.
i'm also not a fan of the rain gauges on the windows or whatever they are called.
i usually don't like CF trunks, but i think it works well with the all CF wing.
i'm also not a fan of the rain gauges on the windows or whatever they are called.
EvoM Staff Alumni
iTrader: (16)
awesome dave, thanks for calling napa. I am not sure why i didnt think of them. CAP, autozone both dont carry them. I found them online but it would take forever to get them. They are definitely packaged 2 count.