Alaska
#4141
Well there is one thing deployments are good for, money! Picked this up yesterday and will be staying at my parents house until I PCS in August. Can't wait to get home and drive it.
http://huntsville.craigslist.org/cto/4167674695.html
http://huntsville.craigslist.org/cto/4167674695.html
#4146
#4148
#4150
Should have it shipped up by August, but here she is. 03 Evo 8 AS with 94k
Mods are:
Exterior:
OEM JDM IX Rear Bumper
Rexpeed D-Style Carbon Front Splitter
Exhaust:
Tomei Expreme Catback
Tomei Test Pipe
Forced Induction:
PTE 6466 T3 0.82 A/R 3" V-Band Discharge
TiAL MV-R 44mm Wastegate
TiAL Q 50mm Blow Off Valve
STM Forward Facing Hot Parts Kit
STM Forward Facing Lower Intercooler Pipe
STM 4" Front Mount Intercooler
STM 3" Upper Intercooler Pipe w/ AIT
GM IAT Sensor w/ SpoolinUp SD Harness
Intake:
Skunk2 Intake Manifold (Ported by STM)
Full Blown Motorsports 70mm Throttle Body
Fuel:
Squash Performance Double Pumper w/ DW300's
FIC 2150cc Injectors
STM Fuel Return Kit
AEM Fuel Rail
FIC Resistor Pack Delete Plug
Cooling:
STM Koyo Half Radiator (-16AN Fittings)
STM Overflow Tank
STM Black Radiator Bracket
Carbign Craft Radiator Cover
OEM -16AN Welded Water Neck
OEM -16AN Welded Thermostat Housing
STM Oil Cooler Delete
Mods are:
Exterior:
OEM JDM IX Rear Bumper
Rexpeed D-Style Carbon Front Splitter
Exhaust:
Tomei Expreme Catback
Tomei Test Pipe
Forced Induction:
PTE 6466 T3 0.82 A/R 3" V-Band Discharge
TiAL MV-R 44mm Wastegate
TiAL Q 50mm Blow Off Valve
STM Forward Facing Hot Parts Kit
STM Forward Facing Lower Intercooler Pipe
STM 4" Front Mount Intercooler
STM 3" Upper Intercooler Pipe w/ AIT
GM IAT Sensor w/ SpoolinUp SD Harness
Intake:
Skunk2 Intake Manifold (Ported by STM)
Full Blown Motorsports 70mm Throttle Body
Fuel:
Squash Performance Double Pumper w/ DW300's
FIC 2150cc Injectors
STM Fuel Return Kit
AEM Fuel Rail
FIC Resistor Pack Delete Plug
Cooling:
STM Koyo Half Radiator (-16AN Fittings)
STM Overflow Tank
STM Black Radiator Bracket
Carbign Craft Radiator Cover
OEM -16AN Welded Water Neck
OEM -16AN Welded Thermostat Housing
STM Oil Cooler Delete
#4152
I'm still debating on bringing it to Alaska. Cost of importing fuel plus I don't wanna ruin it with the ****ty winters. I'm ordering my 2.0LR short block on the 1st from TSComp so hopefully have that done by April.
#4153
#4154
Have you looked at other shops building the 2.0LR motors?? Don't get me wrong Tiago is a good guys just haven't seen anything proven from him. Curious as to why those guys?
Hey Guys, Logan here. I'm currently in Laradise(Laramie), Wyoming. I'm hoping to pick up my '03 Evo VIII in WW this week, super stoked. I've always wanted one!
I'll be back in Alaska about June, can't wait to meet you guys in person.
Attachment 217839
Attachment 217840
I'll be back in Alaska about June, can't wait to meet you guys in person.
Attachment 217839
Attachment 217840
#4155
Then what's the point of spending all that money if you can't enjoy it?? Personally I get smaller injectors and just run it on race gas. But that's just me!
Have you looked at other shops building the 2.0LR motors?? Don't get me wrong Tiago is a good guys just haven't seen anything proven from him. Curious as to why those guys?
Have you looked at other shops building the 2.0LR motors?? Don't get me wrong Tiago is a good guys just haven't seen anything proven from him. Curious as to why those guys?
Boostin Performance built Joey "Junk Box" evo and Strictly Modified with the Green Monster, and both run 2.0LR and have 900 hp. STM's RS also runs a 2.0LR and runs 8.7. It's just a proven motor to get that 8 second time slip. Then I'll probably tone it down for a street car.
Last edited by Evo_AK; Jan 13, 2014 at 03:49 AM.