Mark this thread as Unsold
JMFabrications Intake Manifold w/ BBK1503 TB
May 27, 2008, 12:07 PM
#1
Evolving Member
Thread Starter
iTrader: (5)
Join Date: May 2007
Location: Ashburn, VA
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
JMFabrications Intake Manifold w/ BBK1503 TB
Manifold is sold, BBK Throttle Body and Jackson Automachine Wheel for throttle cable is still available, has quick disconnects to easily wire up to your TPS as well 
$150
$150
Last edited by juice_evo_VII; Jun 9, 2008 at 10:00 AM.
May 27, 2008, 01:31 PM
#3
Evolving Member
Thread Starter
iTrader: (5)
Join Date: May 2007
Location: Ashburn, VA
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
http://www.jmfabrications.com/catalo...products_id=90
At work I'll snap pics tomorrow. But it's exactly as you see there, polished version.
At work I'll snap pics tomorrow. But it's exactly as you see there, polished version.
May 27, 2008, 01:57 PM
#4
Evolving Member
iTrader: (4)
Join Date: Oct 2007
Location: crestwood
Posts: 158
Likes: 0
Received 0 Likes
on
0 Posts
this is a dumb question. but will the stock tb bolt up to it. ( didnt know if you ran a adaptor flange or if the bbk was a direct bolt up) thanks in advance.
May 27, 2008, 02:05 PM
#5
Evolving Member
Thread Starter
iTrader: (5)
Join Date: May 2007
Location: Ashburn, VA
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
JM has adapter flanges to allow the stock TB to bolt up to it for sure. They can also just reweld a stock bolt pattern flange on there if you wanted. But for now the "large bolt pattern" is what it has.
Trending Topics
May 27, 2008, 04:18 PM
#9
Evolving Member
Thread Starter
iTrader: (5)
Join Date: May 2007
Location: Ashburn, VA
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
It was nice, noticeable gains from just bolting on, but mid tuning I had some injector issues, after that the car was under the knife for months, and never finished the build up for any dyno numbers. I'm going with a different setup per the shop I'm with now so I can sell this at a great price for you folks.
Yes comes with the dipstick
May 27, 2008, 04:32 PM
#11
Evolving Member
Thread Starter
iTrader: (5)
Join Date: May 2007
Location: Ashburn, VA
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
It did not during the street tuning or driving. It also was a brand new piece and our fabricator was able to block off the EGR section with a custom plate, gasket, sealant that worked great and we used a new seal with some sealant (suggestion from BBK). I read much about the leaks, and talked to BBK Tech Support about it. But my unit did not demonstrate the condition others have talked about.
Jun 5, 2008, 07:03 PM
#13
Evolving Member
Thread Starter
iTrader: (5)
Join Date: May 2007
Location: Ashburn, VA
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
Manifold is sold, BBK Throttle Body and Jackson Automachine Wheel for throttle cable is still available, has quick disconnects to easily wire up to your TPS as well $150
$150