Mark this thread as Unsold
FS[MidWest]: PART OUT! Sheepey FF turbo setup, AMS IM, COP, block and head, Manley stroker, etc
Oct 18, 2014, 10:23 PM
#1
PART OUT! Sheepey FF turbo setup, AMS IM, COP, block and head, Manley stroker, etc
EVO 8/9 PART OUT! Read the description! Best way to contact me is txt 319-429-five38six
Located in Iowa. Switching to a different platform so everything has got to go! Most are BNIB or minor use. First come first serve, I'm not layaway!
Lowball offers will be laughed at and ignored. All prices are with shipping and PayPal fees.
Evo 8 bare shortblock, bored to 85.5mm, hot tanked, resurfaced, crack check, etc. Comes with cradle, oil pickup and oil pan. Balance shaft bearings are knocked out for new ones. Ready for new internals! PENDING
BNIB Manley turbo tuff I beam rods PENDING
BNIB Manley platinum dish pistons (stroker) 85.5, 9.5:1 CR. $550
BNIB ACL rod/main bearings and thrust washers PENDING
BNIB Cosworth crank scraper SOLD
ARP headstuds (torqued once) $80
Manley 100mm forged crank SOLD
ARP main studs SOLD
MAP Mivec feedline SOLD
Evo 9 mivec head, complete, resurfaced, crack checked, stock ports and valves.
Kelford 280/280 cams
MAP High performance valve springs/retainers
Topline lifters
Kiggly HLA
OEM valve seals
Head will come with a valve cover, brand new VC gaskets and Sheepey CAS covers. PM for details. $1600
BNIB OEM head gasket $70
BNIB Gates timing belt $120
Spoolin up COP setup SOLD
Spoolin up speed density harness $30
AMS f1 Intake manifold, can include spacer and 2 gaskets SOLD
BNIB Sheepey FF hot parts, side exit and regular downpipe, t3 flange $1900
PTE 6262 (one start up) t3 and true 3" vband out .82a/r. $800
BNIB Avid motor mounts (all 4) SOLD
Exedy twin disk with monoloc, less than 2k miles, flywheel has a crack. Look at pictures below. $700
BNIB AEM fuel rail and fuel pressure regulator. SOLD
No name harness bar with Corbeau harness. SOLD
VRSF Intercooler 3.5" SOLD
Tial Q BOV $200
OMNI 4 bar map sensor SOLD
STM SS clutch line $50
STM clutch fork stop SOLD
Grimmspeed EBC SOLD
MAP oil feed line 4AN with inline filter and STM oil return line 10AN, combo SOLD
AEM Wideband $150
Gruppe S gauge pod 60mm $300
Tstat housing and water pipe, 16AN fittings welded on, coolant lines included SOLD
Tstat housing and water pipe, powdercoated, off of a Evo 8. $120
OEM balance shaft that we're CNCed. $120
Non ACD tcase with death whine, doesn't have a tail stock, not sure of condition. Good for a rebuild. $450
Located in Iowa. Switching to a different platform so everything has got to go! Most are BNIB or minor use. First come first serve, I'm not layaway!
Lowball offers will be laughed at and ignored. All prices are with shipping and PayPal fees.
Evo 8 bare shortblock, bored to 85.5mm, hot tanked, resurfaced, crack check, etc. Comes with cradle, oil pickup and oil pan. Balance shaft bearings are knocked out for new ones. Ready for new internals! PENDING
BNIB Manley turbo tuff I beam rods PENDING
BNIB Manley platinum dish pistons (stroker) 85.5, 9.5:1 CR. $550
BNIB ACL rod/main bearings and thrust washers PENDING
BNIB Cosworth crank scraper SOLD
ARP headstuds (torqued once) $80
Manley 100mm forged crank SOLD
ARP main studs SOLD
MAP Mivec feedline SOLD
Evo 9 mivec head, complete, resurfaced, crack checked, stock ports and valves.
Kelford 280/280 cams
MAP High performance valve springs/retainers
Topline lifters
Kiggly HLA
OEM valve seals
Head will come with a valve cover, brand new VC gaskets and Sheepey CAS covers. PM for details. $1600
BNIB OEM head gasket $70
BNIB Gates timing belt $120
Spoolin up COP setup SOLD
Spoolin up speed density harness $30
AMS f1 Intake manifold, can include spacer and 2 gaskets SOLD
BNIB Sheepey FF hot parts, side exit and regular downpipe, t3 flange $1900
PTE 6262 (one start up) t3 and true 3" vband out .82a/r. $800
BNIB Avid motor mounts (all 4) SOLD
Exedy twin disk with monoloc, less than 2k miles, flywheel has a crack. Look at pictures below. $700
BNIB AEM fuel rail and fuel pressure regulator. SOLD
No name harness bar with Corbeau harness. SOLD
VRSF Intercooler 3.5" SOLD
Tial Q BOV $200
OMNI 4 bar map sensor SOLD
STM SS clutch line $50
STM clutch fork stop SOLD
Grimmspeed EBC SOLD
MAP oil feed line 4AN with inline filter and STM oil return line 10AN, combo SOLD
AEM Wideband $150
Gruppe S gauge pod 60mm $300
Tstat housing and water pipe, 16AN fittings welded on, coolant lines included SOLD
Tstat housing and water pipe, powdercoated, off of a Evo 8. $120
OEM balance shaft that we're CNCed. $120
Non ACD tcase with death whine, doesn't have a tail stock, not sure of condition. Good for a rebuild. $450
Last edited by Czarcasm; Oct 22, 2014 at 11:46 PM.
Oct 23, 2014, 01:19 AM
#7
Sheepey CAS covers
Bump for nice parts and a question: Sheepey CAS covers!
Tried talking to Sheepey about how to install these, but no telephone # only email?!? I have new oem cas and don't want to cause a leak or not get them off?!?
How easy are these to install?
Thanks!
Tried talking to Sheepey about how to install these, but no telephone # only email?!? I have new oem cas and don't want to cause a leak or not get them off?!?
How easy are these to install?
Thanks!
Trending Topics
Oct 23, 2014, 05:03 AM
#8
They're pretty simple to install, take the old ones off and put the new covers on. Sheepeys covers have O rings instead of silicone/sealer Mitsu puts on from factory. As for the contact issue, lol... I had the same problem. Alexander Soto is your guy, contact him on FB. Owner of sheepeybuilt
Thread
Thread Starter
Forum
Replies
Last Post
tscompusa
Evo Dyno Tuning / Results
9
Sep 21, 2016 08:55 PM
Czarcasm
Project Cars / Build Threads
4
Aug 17, 2014 04:23 PM
FS[Northeast]: Manley Turbo Tuff 100mm Crank stroker/Manley Platinum Series Lightweight Pistons 2.3L
usacchamp
For Sale/WTB - Engine / Drivetrain / Power
16
Jul 13, 2014 10:22 AM
SBR INC
Evo Vendor 'Group Buy / Specials' Classifieds
2
Oct 16, 2009 06:33 AM