EvolutionM - Mitsubishi Lancer and Lancer Evolution Community

Notices

STM Releases the new STM 650 cam shafts.

Thread Tools
 
Search this Thread
 
Old Oct 10, 2011, 04:58 PM
  #46  
Evolved Member
iTrader: (94)
 
EvoDan2004's Avatar
 
Join Date: Feb 2005
Location: New Jersey
Posts: 8,984
Likes: 0
Received 7 Likes on 7 Posts
Originally Posted by David Buschur
I have tested them, more top end power just like Emery says. I agree with Emery on the HP and RPM requirements to run them.

i am so annoying. now i know why you have a flat spot on your four head. its from pounding your head into the wall because of me. and maybe a few others haha.

what about the mid range. how much RPM are we loosing in spoolup. do i need them? probably not but i am always looking for the edge you know.
EvoDan2004 is offline  
Reply Like
Old Oct 10, 2011, 08:44 PM
  #47  
Evolved Member
iTrader: (3)
 
Evosick2332's Avatar
 
Join Date: Dec 2008
Location: Illinois
Posts: 2,407
Likes: 0
Received 1 Like on 1 Post
Heres the car in action this past weekend running 9.1@159.88. Clocks were off because the car next to me had clocks off which makes me not show the times. Built 2.0 10:5:1 Built Head STM 650 Cams. Ill get the idling video uploaded that i made to show everyone how the car sounds at idle

http://www.youtube.com/watch?v=y8hrDPKZ6x0
Evosick2332 is offline  
Reply Like
Old Oct 10, 2011, 09:42 PM
  #48  
Evolved Member
iTrader: (51)
 
LGshow19's Avatar
 
Join Date: Feb 2010
Location: San Antonio
Posts: 1,640
Likes: 0
Received 0 Likes on 0 Posts
Damn you stayed in it late didnt you lol nice run...
LGshow19 is offline  
Reply Like
Old Oct 11, 2011, 11:17 AM
  #49  
Evolved Member
iTrader: (3)
 
Evosick2332's Avatar
 
Join Date: Dec 2008
Location: Illinois
Posts: 2,407
Likes: 0
Received 1 Like on 1 Post
Originally Posted by LGshow19
Damn you stayed in it late didnt you lol nice run...
LOL yea i did, wanted to make sure i was through the trap hahaha
Evosick2332 is offline  
Reply Like
Old Oct 11, 2011, 11:21 AM
  #50  
Evolving Member
iTrader: (24)
 
ilikeppie's Avatar
 
Join Date: Dec 2008
Location: Fort Collins, Colorado
Posts: 407
Likes: 0
Received 0 Likes on 0 Posts
Nice clean run! would def like to get a video of this idling too!
ilikeppie is offline  
Reply Like
Old Oct 11, 2011, 11:47 AM
  #51  
Evolved Member
iTrader: (3)
 
Evosick2332's Avatar
 
Join Date: Dec 2008
Location: Illinois
Posts: 2,407
Likes: 0
Received 1 Like on 1 Post
Originally Posted by ilikeppie
Nice clean run! would def like to get a video of this idling too!
Ill try to get the idling video up tonight for everyone
Evosick2332 is offline  
Reply Like
Old Oct 11, 2011, 02:34 PM
  #52  
Evolving Member
iTrader: (24)
 
ilikeppie's Avatar
 
Join Date: Dec 2008
Location: Fort Collins, Colorado
Posts: 407
Likes: 0
Received 0 Likes on 0 Posts
Right on man thanks!
ilikeppie is offline  
Reply Like
Old Oct 15, 2011, 07:53 PM
  #53  
Evolving Member
iTrader: (5)
 
S13 Curtis's Avatar
 
Join Date: Apr 2009
Location: Orlando,FL
Posts: 275
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by Evosick2332
Ill try to get the idling video up tonight for everyone
Idleing video please, im very interested.
S13 Curtis is offline  
Reply Like
Old Oct 16, 2011, 01:07 PM
  #54  
Evolved Member
iTrader: (31)
 
evoracingstar's Avatar
 
Join Date: Oct 2005
Location: C.T
Posts: 1,525
Likes: 0
Received 1 Like on 1 Post
sick cam. would it be realistic for me i have hta 86 with a fully built 2.0 .20 over im running cosworth 272 right now. should i switch to these. bc ill be maken right around that power range if not more??
evoracingstar is offline  
Reply Like
Old Oct 16, 2011, 01:09 PM
  #55  
Evolved Member
iTrader: (31)
 
evoracingstar's Avatar
 
Join Date: Oct 2005
Location: C.T
Posts: 1,525
Likes: 0
Received 1 Like on 1 Post
ops just realized these r for a evo 8!
evoracingstar is offline  
Reply Like
Old Oct 18, 2011, 12:56 PM
  #56  
Evolved Member
iTrader: (3)
 
Evosick2332's Avatar
 
Join Date: Dec 2008
Location: Illinois
Posts: 2,407
Likes: 0
Received 1 Like on 1 Post
Sorry for the delay on the idling video. I will get it up this week for sure. I did go to the track again this Saturday and had success. I managed to go a little faster and 1 pass trap 163.9 MPH! Car has a 8 sec pass in her. Car is spinning a lot in first gear especially towards the end of the night. I'm hoping this weekend it will hook up a little more! Videos from the weekend are posted below. STM 650s cams FTW!!

http://www.youtube.com/watch?v=X9M49...&feature=share

http://www.youtube.com/watch?v=yNw98...&feature=share
Last edited by Evosick2332; Oct 18, 2011 at 12:58 PM.
Evosick2332 is offline  
Reply Like
Old Dec 18, 2011, 10:09 PM
  #57  
Evolved Member
iTrader: (100)
 
yellowevo82's Avatar
 
Join Date: Nov 2005
Location: Mayfield, Pa
Posts: 1,443
Received 108 Likes on 86 Posts
jesus^^^
yellowevo82 is offline  
Reply Like
Old Dec 22, 2011, 01:02 PM
  #58  
Former Sponsor
Thread Starter
iTrader: (79)
 
EmeryatSTM's Avatar
 
Join Date: Jun 2007
Location: Rochester, NY
Posts: 2,340
Likes: 0
Received 3 Likes on 3 Posts
I think we have one set left on the shelf. If anyone wants a set get them now because I don't think we will be making them again.


-Em
EmeryatSTM is offline  
Reply Like
Old Dec 10, 2014, 09:51 AM
  #59  
Former Sponsor
iTrader: (4)
 
STM Tuned's Avatar
 
Join Date: Jan 2013
Location: Rochester, NY
Posts: 702
Received 13 Likes on 13 Posts
Bump, Have these In-Stock and ready to ship

-Ethan
STM Tuned is offline  
Reply Like
Old Jan 21, 2015, 02:27 PM
  #60  
Former Sponsor
iTrader: (4)
 
STM Tuned's Avatar
 
Join Date: Jan 2013
Location: Rochester, NY
Posts: 702
Received 13 Likes on 13 Posts
Got a few more sets in. Give us a call at 585-226-8226

-Ethan
STM Tuned is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
STM Has Your Cam Needs Covered! Kelford, GSC's, Cosworth, HKS and MORE!
STM Tuned
Evo 'For Sale' Engine Internals and Drivetrain
34
Feb 3, 2016 02:00 PM
STM 650 cams! IN STOCK !
STM Tuned
Evo Vendor 'Group Buy / Specials' Classifieds
19
Aug 27, 2015 02:38 PM
STM 650 Cams for Evo VIII Group Buy (Spring 2013)
STM Tuned
Evo Vendor 'Group Buy / Specials' Classifieds
31
Oct 29, 2013 10:28 AM
FS: STM's 05 Evo RS
EmeryatSTM
For Sale - Cars For Sale
102
Apr 28, 2013 06:45 PM
For sale NY Evo 8 ( Ricer)
EmeryatSTM
For Sale - Cars For Sale
33
Nov 3, 2011 06:35 PM
Tags
Back to Subforum
Vendor Announcements
View Next Unread
**NEW RELEASE** Manley's Billet Crankshaft for DSM and Evo Now Available!!




Advanced Search
Quick Reply: STM Releases the new STM 650 cam shafts.


Reply Closed Thread Share

All times are GMT -7. The time now is 12:37 PM.